User manual ZONET ZPS2000

[. . . ] TABLE OF CONTENTS COPYRIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PRODUCT OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 COMPONENTS AND FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you have Windows XP and the Windows Firewall is enabled you will see this window pop-up message when the MFP server utility is first launched. Make sure you click the 12 unblock button to allow communication with the MFP server. Other software firewalls may display similar options ­ make sure the MFP server software is allowed to bypass such programs. 16. The MFP server utility will search your network for the MFP server and display it in the window. If no MFP server is found, please make sure any third party firewalls have been disabled or bypassed and click the Search button to try again. Note: 13 The default IP address of MFP server is 192. 168. 0. 10, and subnet mask is 255. 255. 255. 0. If the MFP server utility didn't find MFP server, please make sure of the MFP server and your computer's IP segment are the same, e. g. Click the "+" in front of the MFP server name to show the name of the attached printer. Then select the printer name and click the Connect button in the MFP server utility. 18. The printer should be detected as if it was plugged directly into the computer. If you would like the connection to this printer to be restored automatically when the MFP server utility launches, you will need to add the device to your favorites list. Click the "+" in front of Connected devices and right-click the name of the printer. Click OK to confirm that the printer is in your favorites list. 21. Once you have connected to the MFP server you can close the MFP server utility. Be sure to use the close box with an X in the top right corner so that the MFP server utility continues to run in the background. The large button labeled Exit will shut down the MFP server utility and disconnect your computer from the printer. 22. From Windows 2000/XP system, go to start -> Printers and Faxes and make sure of the icon of MFP printer appeared. 23. Note: 15 If you wish to setup more MFP servers, start setup utility from your Windows Start menu: start -> All Programs -> Remote Virtual USB -> Remote Virtual USB and repeat the setup procedure. Uninstalling the setup utility on Windows 2000/XP Computer Please follow the directions listed below to proceed with the un-installation procedure. After the MFP server setup utility is removed, the MFP server is no longer accessible. You have to re-install it on your system in order to access the MFP server again. Procedure: 1. Click start, and select Control Panel. 2. Double click the Add or Remove Programs icon. 16 3. Select Remote Virtual USB, and click Change/Remove button. 4. Follow the directions on the screen to complete the un-installation procedure. 17 4. Configuration from Embedded Web Server Overview The MFP server contains an embedded web server that can be accessed through a supported web browser on a LAN, for example, IE 5. 01, Netscape 6. 2 or above is recommended. [. . . ] If the connectors are damaged, contact your dealer for a replacement connector. 28 Appendix: Load Default Setting 1. The MFP server will restart. WARNING: This will erase all settings of MFP server to default and should be performed with caution!After performing a factory default, the default settings will be: DHCP client: off IP address: 192. 168. 0. 10 Subnet Mask: 255. 255. 255. 0 Or, you can load the default setting from the WEB management as following: Reboot the MFP server: 1. Press the reset button once, and then release it. 29 Or, you can click the Restart button from the WEB management as following: WARNING: This will restart the MFP server and stop all on-going and pending job jobs! 30 How to Scan via MFP Server You can use the proprietary utility of MFP printer, e. g. [. . . ]