User manual ZEBRA P330M

[. . . ] Zebra® P330i & P330m Card Printer User's Manual 980459-001 Rev C Foreword This manual contains installation and operation information for the Zebra P330i and P330m Card Printers manufactured by Zebra Technologies Corporation, Camarillo, California. The only difference between these models is that the P330i supports full-color ribbons (which may include a protective overcoat panel), and the P330m supports monochrome color printing only. In this manual, references that are specific to the P330i or P330m will be identified as such; references that apply to both models will use the term "the printer. " Return Materials Authorization Before returning any equipment to Zebra Technologies Corporation for in-warranty or outof-warranty repair, contact Repair Administration for a Return Materials Authorization (RMA) number. Repack the equipment in the original packing material and mark the RMA number clearly on the outside. [. . . ] · Printer Properties are set (the factory default values will be appropriate for many applications). · Card printing is directed by the appropriate application software program. Setting Printer Properties Printer Properties can be set either at the Operating System level or within the application software program used for printing cards. Note · In the following description of setting Printer Properties, only those properties and options that are suitable for being set by the User are described. The User should not make selections or set parameters unless they are specifically described in this section Preferences settings can configure the printer for Landscape (wide) or Portrait (tall) printing orientation, and allow the user to verify that the desired ribbon is installed in the printer. (Monochrome ribbons are selected via the drop-down menu. ) If the printer includes the optional magnetic card stripe encoder, encoding parameters and coercivity can be set. Printer cleaning can be initiated from the Tools window (printer cleaning can also be initiated at the printer; see Chapter 4). Also from the Tools window, the Test Card can be selected from several pre-loaded styles. 980459-001 Rev C P330i & P330m Card Printer User's Manual 25 Printing a Card Printing a Sample Card "Single Feed Options" allows Disabling or Enabling Single Feed Support. · If "Disable Single Feed Support" is selected, when the printer runs out of cards in the feeder, the LCD display will read OUT OF CARDS. · If "Enable Single Feed Support" is selected, when the printer runs out of cards in the feeder it will wait until a card is inserted in the single-card slot or cards are loaded in the feeder, and then will automatically continue. Printing a Sample Card Sample card designs are installed with the printer driver. Sample cards require Microsoft Word or Microsoft Paint application software. Select Start, select Programs, select Zebra Card Printers, and select a sample card, or follow the directions below to design a card. Depending on your computer configuration this may be done by double-clicking an icon on your desktop, or by clicking the Windows Start icon, selecting Programs, and navigating to Microsoft Word 2. Select the Margins tab, and set the Top, Bottom, Left, and Right margins to 0 (zero). Design a card with both black and colored text and with colored pictures (see example below). us!http://www. zebracard. com Note · For cards thinner than 20 mils (0. 51 mm), the card design must be limited to (1) no more than two 30 mm x 30 mm areas of full color, (2) black information (text and barcode, for example) must cover no more than 50% of the card area, and (3) there must be at least a 5mm unprinted border along all edges. For cards thicker than 40 mils (1. 02 mm), the card design must have at least a 5mm unprinted border along all edges. For cards with thickness between 20 mils (0. 51 mm) and 40 mils (1. 02 mm), these restrictions do not apply; full color printing is permitted edge to edge in both directions. 26 P330i & P330m Card Printer User's Manual 980459-001 Rev C Printing a Card Feeding One Card at a Time 8. If the printer was not selected as the default printer, go to the File menu, select Print Setup and choose Zebra P330i Card Printer (or Zebra P330m Card Printer) from the printer names list. The printer will feed in a card and start printing (the data download time will vary depending on the complexity of the card design and the processing speed of your computer). 11. Once the printing job is complete, the card is ejected from the printer. Feeding One Card at a Time A Manual Feed Slot is available below the Card Input Hopper for feeding single cards. The Card Input Hopper must be empty for single-card feeding to work properly. 1. Verify that there are no cards in the feeder, then close the Card Feeder cover. 2. Do not feed more than one card at a time. Note · If single-card feeding will be the normal mode of operation, you may select that mode through the driver software. [. . . ] For more information about Card Media and Ribbons available from Zebra Technologies Corp. , please refer to the Media List on the Windows Drivers and User Documentation CD supplied with this printer. (This applies to P330i only. ) Card Specifications · · · · · · Types: PVC or Composite Card Width/length ISO CR-80 - ISO 7810, 2. 125" (54 mm) x 3. 375" (86 mm) Option: Magnetic Stripe - ISO 7811 Card thickness: 10-60 mil (0. 25-1. 5 mm) ± 10% Card feeder capacity: up to 100 cards (30mil) (Optional high-capacity feeder: up to 220 cards) Card output hopper capacity: 100 cards (30mil) 980459-001 Rev C P330i & P330m Card Printer User's Manual 43 Technical Specifications Bar Codes Bar Codes · · · · Code 39, Code 128 B & C with & without check digit 2 of 5 and 2 of 5 interleaved UPC-A, EAN8, and EAN13 PDF-417 2D bar code and other symbologies available via Windows printer driver Fonts · · Arial and Arial Bold True Type fonts available via Windows Driver Card Dimensions ISO Standard 7810 Dimensions for Plain Card 2. 125 ± 0. 002 in (53. 98 ± 0. 050 mm) Radius 0. 125 in (3. 18 mm) 3. 375 ± 0. 01 in (85. 72 ± 0. 25 mm) 0. 009 ~ 0. 033 in (0. 23 ~ 0. 84 mm) ISO Standard 7811 Dimensions for Magnetic Stripe Card 0. 623in (15. 82mm) min 0. 218in (5. 54mm) ma 0 ~ 0. 115in (2. 92mm) max 0 ~ 0. 115in (2. 92mm 44 P330i & P330m Card Printer User's Manual 980459-001 Rev C Technical Specifications Bi-Directional Communications Interfaces Contact Location for Smart Card ISO Standard 7816 0. 757 in (19. 23 mm) 1. 124 in (28. 55 mm) 0. 403 in (10. 25 mm) 0. 782 in (19. 87 mm) Bi-Directional Communications Interfaces · · USB Built-in Ethernet (optional) Mechanical Specifications · · · · Width: 18. 2 in (462 mm) Depth: 9. 4 in (239 mm) Height: 10. 1 in (256 mm) Weight: 15. 5 lbs (7 kg) Electrical · · 110 ~ 230 Volts AC ± 10% (100 - 254 V), 60 ~ 50 Hz ± 3Hz (47 - 63 Hz) FCC Class A, CE, UL, and CUL approved Environmental · · · · · Operating Temperature: 60°F to 86°F (15°C to 30°C) Operating Humidity: 20% to 65% non condensing Storage Temperature: 23°F to 158°F (-5°C to 70°C) Storage Humidity: 20% to 70% non-condensing Ventilation: Reasonably dust free air environment Options · · · · · Built-in Ethernet network communications Three track magnetic stripe encoder (standard and reverse) High capacity feeder (220 30-mil cards) Contactless encoding (MIFARE and HID iCLASS) Contact encoding (Station and encoder) 980459-001 Rev C P330i & P330m Card Printer User's Manual 45 Technical Specifications Options 46 P330i & P330m Card Printer User's Manual 980459-001 Rev C APPENDIX A Magnetic Card Encoder Introduction This Appendix includes operation and maintenance requirements for the P330i or P330m Printer with the optional magnetic card stripe encoder. (See Chapter 2 for location of the Magnetic Card Stripe Encoder. ) The magnetic encoder can be set for either high or low coercivity. Use the printer driver to change the encoder setting. Media Loading Orientation The magnetic encoder may be installed with the read/write head positioned below the card path. [. . . ]