User manual ZANUSSI FLS824CN
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ZANUSSI FLS824CN. We hope that this ZANUSSI FLS824CN user guide will be useful to you.
You may also download the following manuals related to this product:
ZANUSSI FLS824CN (740 ko)
ZANUSSI FLS824CN (759 ko)
ZANUSSI FLS824CN (680 ko)
Manual abstract: user guide ZANUSSI FLS824CN
Detailed instructions for use are in the User's Guide.
[. . . ] Before washing ensure that all pockets are empty and buttons and zips are fastened. Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp material can cause extensive damage and must not be placed into the appliance nor left in the pockets. Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grease before washing. Garments which have been in contact with volatile petroleum products should not be machine washed. [. . . ] 5
22
Levelling
Level the appliance by loosening or tightening the feet. Once in the right position fix the feet by pushing the nuts against the base of the case. Accurate levelling will prevent vibration, noise and displacement of the appliance during operation. If posible always place the appliance on a solid floor.
P0254
P0509
Hydraulic connection
There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4 gas for the water supply, a sink, a wash basin or a drainage system in the wall. If not, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Place the enclosed rubber joint, delivered in a plastic bag together with the appliance (A), at the very end of the inlet hose and carefully screw the pipe to the tap taking care not to damage the screwdrive and fix the nut well on to the end in order to avoid leaking. If necessary turn the hose adequately by unscrewing the nut at the rear of the appliance. (Open the tap and assure that it does not leak and close it again. ) Place the discharging hose in a washbasin or sink with the aid of the bent piece delivered separately. The bent piece has to be entered into the tube's mouth in order to assure the support. This piece allows the hose to be fixed to the wall by means of an opening on the upper part and that way the hose does not move and its falling is avoided.
P0021
A
AL013
P0022
23
IMPORTANT: The distance from the floor to the highest part of the hose should be between 60 to 90 cm. Should a extension of the discharging hose be unavoidable this must never surpass 1. 5 m and must be of the same diameter as the original hose. Agents dosage
If you wish to use agents pour the fabric softener into the compartment with the symbol and the bleach into the compartment with the symbol Never exceed the MAX level.
4. Select the temperature
Tur n the dial clockwise to the desired temperature.
AL022
5. Select the program
Turn the dial clockwise until the marker reaches the desired program.
27
6. Start
Before pulling the program selector check if: s The door is properly closed.
s s s s
The appliance is plugged in. The drain hose is adequately positioned.
2
Pull the program selector towards you till it clicks. Stop
P0215
ALO26
The washing machine stops automatically once the cycle is finished, the on/off lamp goes off. Open the door 3 minutes after the end of the program to give the safety device time to unlock. Push the program selector in, close the tap, and unplug the appliance. Leave the door ajar for a few minutes for the steam to get out.
IMPORTANT REMARK: This appliance is provided with a security device to avoid opening during the cycles. Open it only when absolutely necessary and wait 3 minutes after you have stopped the machine to give the safety device time to unlock.
28
PROGRAMS
Programs for cotton and linen
Recommended load: max. 4, 5 kg.
PROGRAM DEGREE OF SOIL heavy soil COMPARTMENTS TO USE MAXIMUM PROGRAM WATER POSITION TEMP. [. . . ] This way you make sure no water at all remains in the appliance which could freeze and thus damage it and its surroundings. When you need to start the machine up again, make sure that the room temperature is above 0°C.
33
Cleaning the filters
The drain filter
A clean filter is important for correct functioning of the washing machine, and it should therefore be cleaned regularly. Small objects left in the pockets and yarn is retained here.
AL012
AL010
Unscrew the filter completely turning it counterclockwise. Attention Never remove the unloading filter while the washing machine is operating. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ZANUSSI FLS824CN
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ZANUSSI FLS824CN will begin.