User manual WHISPER CREEK ARCHERY COMPOUND BOW 2005

[. . . ] 2005 Compound Bow Owner's Manual Table of Contents Whisper Creek Mission Bow Terminology Safety Instructions Care Instructions Cam Performance Draw Length Adjustments Let-Off Adjustments Draw Weight Adjustments Bow Press Instructions Proofs of Technology Whisper Creek Technology 3 4 5 6 7 9 11 11 12 13 15 WHAT SETS US APART We can assure you that no other bow company has the technology that Whisper Creek Archery has. Whisper Creek Archery is light-years ahead of others when comparing to "Compound Bow" Technology. Our mission at Whisper Creek Archery is to provide you with the highest quality and most technologically advanced bow in the industry. Through extensive research and development, our technology provides the archer with the quietness, precision, speed, and versatility that are needed to perform the job well. [. . . ] To change out the module, place the bow into a bow press (WARNING: strings MUST be relaxed in order to change out the draw modules), and remove the fasteners. Replace the new module into the designated slot as noted on the cam by slightly pulling up on the module where noted in figure (WARNING: Do not over bend module where module will not flex back into position) and fasten the module to the cam. Note that it is IMPORTANT that the cleats be seated into position prior to fastening. (WARNING: always make sure that you use blue loc-tite when replacing modules and tighten fasteners securely). CounterFORCE cps& 1/2 The Whisper Creek CPS & 1/2 system has a range of 5 1/2 inch draw length adjustment using 3 inter-changeable draw modules. Each draw module, numbered 1 through 3, has a full 1 1/2 inches of draw length adjustment. Adjustments can be made in 1/8" increments using the string anchor post on the control wheel (top, or 1/2" increments using the sliding modular on the power cam (bottom). An exact draw length can be achieved using a combination of these methods. A bow press must be used to adjust the modular and the string anchor post. SLIDING MODULAR The CPS modular is located on the power cam. It can be adjusted by removing both flathead screws and sliding the modular from position 1 through 4 (position one being the shortest draw and 4 being the longest). A full inch of adjustment in 1/2-inch increments can be obtained this way. STRING ANCHOR POST The string anchor post can be found on the control wheel. Remove the flat head screw and slide the post to the desired position A through D (position A being the shortest and D being the longest). This system is so efficient that no stabilizer and/or limb damping accessories are needed. We absolutely guarantee no vibration (twang) within the PS (BowACTUATORTM Suspension Technology) Series type bows. In order to prove this claim, a simple test can be performed: Steps To Prove How Technology Works: 1. Take a Stealth "bare" with only string leeches on the string. Take a Stealth "loaded" with a stabilizer, Limb LimbSavers, cable rod LimbSavers, and string leeches on the string. First shoot the Stealth "bare" with only string leeches then 6. Shoot the Stealth "loaded" with stabilizer & damping accessories then 7. Shoot the Innovator "bare" with only string leeches You will find that the Innovator "bare" (apples to apples) is much smoother and quieter with no hand shock than the Stealth that is completely loaded with the damping accessories. If you add a stabilizer to the Innovator during the test, you will no difference in feel with/without the stabilizer. Notice how the vibration in the projected oscillation curve dies out within the Innovator versus the more traditional bows such as the Stealth. WHISPER CREEK TECHNOLOGY POCKET TECHNOLOGY BowACTUATORTM Technology BowSUSPENSIONTM Technology Patented BowACTUATORTM Suspension Technology · The BowACUATORTM Suspension Technology is the last line of defense for vibration ­ it's so efficient in eliminating all vibration that a stabilizer is no longer required. The BowACUATORTM Suspension Technology gives smoothness a whole new name without sacrificing a lot of speed. [. . . ] The BowDAMPTM Material is excellent for low to high impact with repetitive pounding such as the use with compound bows!The BowDAMPTM Material will not swell or deteriorate in water where most plastics and/or elastomers will. BowDAMPTM Material Technology was designed to resist high impact as well as having "outstanding" abrasive resistance. Its abrasive resistance is about 20 times better than that of steel - that's right steel! [. . . ]