User manual WHIRLPOOL WDF310PLAB USE & CARE GUIDE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual WHIRLPOOL WDF310PLAB. We hope that this WHIRLPOOL WDF310PLAB user guide will be useful to you.


WHIRLPOOL WDF310PLAB USE & CARE GUIDE: Download the complete user guide (4191 Ko)

You may also download the following manuals related to this product:

   WHIRLPOOL WDF310PLAB ENERGY GUIDE (373 ko)
   WHIRLPOOL WDF310PLAB DIMENSION GUIDE (214 ko)
   WHIRLPOOL WDF310PLAB INSTALLATION GUIDE (12235 ko)
   WHIRLPOOL WDF310PLAB WARRANTY INFORMATION (127 ko)

Manual abstract: user guide WHIRLPOOL WDF310PLABUSE & CARE GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] • If necessary, the power cable may be replaced with one the same obtained from our After-Sales Service. For appliances with water-stop system: The water inlet hose and plastic casing contain electrical components. Load capacity: -12 place settings • • • EC Declaration of Conformity This appliance has been designed, constructed and distributed in compliance with the safety requirements of EC Directives: • 73/23/EC • 89/336/EC • 93/68/EC. ENERGY AND WATER SAVING TIPS • • Do not rinse crockery under running water. Always fully load the dishwasher before switching on or set the wash programme to half load (if available) if one rack only is loaded. [. . . ] Important: Only use regeneration salts recommended for use in domestic dishwashers. Do not fill the salt container with detergent as this will cause irreparable damage to the water softener system. To fill the salt container: 1. If the dishwasher is new, fill the salt container to the rim with water. Screw the cap back on by turning it clockwise. Electric indicator: The salt level indicator lamp on the control panel illuminates when the salt container is empty. Visual indicator: The red float is clearly visible in the cap window when the salt container is full. The red float lowers and is no longer visible when the salt container is empty. Salt level indicator The dishwasher is equipped with an electric or visual salt level indicator depending on the model installed. 14 HOW TO FILL THE RINSE AID DISPENSER The rinse aid facilitates drying and prevents the formation of unsightly spots and streaks on crockery. Before using the dishwasher for the first time, fill the rinse aid dispenser. Fill the dispenser with rinse aid up to the dashed line (about 100 ml maximum). Immediately wipe away any spilt rinse aid to prevent excess suds which may spoil washing results. Replace the cap. A How to adjust the rinse aid dosage regulator. (Open the cover and close again following adjustment). Factory setting: 3 If you are not satisfied with washing or drying results, change the dial setting with a spoon handle or coin. • If the hose length does not suffice, replace with similar hoses obtained from your local dealer or our After-Sales Service. • The inlet hose must be securely clamped to the water tap to prevent leaks. • The inlet water temperature varies according to the model installed: inlet hose marked “25°C max. ”: maximum temperature 25°C All other models: maximum temperature 60°C. • When installing the appliance, make sure the drain water discharges correctly and, if necessary, remove the wire gauze from the sink siphon. • Secure the drain hose with a clamp to the siphon to prevent it from dropping off during operation. • For appliances with water-stop system only: if the water connections are made correctly, the water-stop system safeguards your home against damage caused by flooding. Electrical connections: • Closely adhere to local Electricity Board regulations. • Voltage information is shown on the rating plate mounted inside the door on the right hand side. • The power cable must only be replaced by a qualified technician. 18 CONNECTIONS 1) ELECTRICAL CONNECTIONS “Warning - this appliance must be earthed” This appliance is normally supplied with a mains lead having a plug fitted in the factory which has been checked for correct earth continuity. If the fitted plug is not suitable for your socket outlet, or if the machine’s mains lead is not fitted with a plug, you should fit a suitable new, good quality plug by following the instructions in (2) below. Any unsuitable plug should be cut off and disposed of in order to avoid a possible shock hazard should it be inserted into a socket. [. . . ] The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the letter “E” or by the Earth symbol or coloured yellow or green and yellow. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured black. The BROWN wire must be connected to the terminal which is marked with the letter “L” or coloured red. For all other types of plug, the supply socket should be protected by a 16 A fuse or circuit breaker at the distribution board 19 MAINTENANCE AND CLEANING Before cleaning or carrying out maintenance, press the ON/OFF button. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL WDF310PLAB




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL WDF310PLAB will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.