User manual WHIRLPOOL AKT424WH

[. . . ] Do not repair or replace any part of the appliance unless specifically stated in the user manual. TECHNICAL INFORMATION FOR THE INSTALLER • • This product can be embedded in a worktop 20 to 60 mm thick. If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. [. . . ] IMPORTANT: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. • After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs from max position to check flame stability. to minimum position C C A B C 5019 319 01838 Manufacturer: Whirlpool Europe S. r. l. Borghi, 27 21025 Comerio (VA) ITALY ELECTRICAL CONNECTION WARNING WARNING This operation must be performed by a qualified technician. • REPLACING THE INJECTORS (see the injector table in the Instruction) • • • Remove grids (A). Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector to be replaced. • Replace it with the injector suitable for the new type of gas. • If you have a multiple crown burner use side spanner to replace the injector (E). Before installing the hob, remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration. The electrical connections must L comply with local regulations. Earth • The earthing of this appliance is (yellow/green) compulsory by law. • IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate. ASSEMBLY After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure. ADJUSTING MINIMUM GAS SETTING OF TAPS Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction. NOTE: the power supply cable must be long enough to permit its upward extraction. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop (see the following figures). Top 20 mm Top 40 mm 20 40 To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows: • tighten screw to reduce the flame height (-); • loosen screw to increase the flame height (+). The adjustment must be performed with the tap in minimum gas setting position (small flame) . • At this stage, light up the burners and turn the knobs from max position to minimum position to check flame stability. Upon completion of adjustment, reseal using sealing wax or an equivalent material. Top 30 mm 30 Top 60 mm 60 REFERENCE TO LOCAL REGULATIONS Ensure that the installation and gas connections are performed by a qualified technician, following the manufacturer's instructions and in compliance with current local safety regulations. ADJUSTMENT TO DIFFERENT TYPES OF GAS WARNING This operation must be performed by a qualified technician. AFTER-SALES SERVICE Before calling the After-Sales Service, make sure you can give the following information: -type of fault or problem; -exact model (written on the label affixed to the instruction/warranty); -service number that follows the word SERVICE on the rating plate under the hob and on the label affixed to instruction/warranty; -your complete address and phone number. -If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty. If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors. Remove the information label and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Instruction. [. . . ] Burner Ultra-rapid Semi-rapid Auxiliary Pot Ø From 24 to 26 cm From 16 to 22 cm From 8 to 14 cm INJECTORS TABLE Type of gas used Type of burner Injector marking Rated thermal flow rate kW NATURAL GAS (Methane) G20 LIQUEFIED PETROLEUM GAS (Butane) G30/G31 Type of gas used G20 20 mbar G30/G31 37 mbar Ultra-rapid Semi-rapid Auxiliary Ultra-rapid Semi-rapid Auxiliary Model configuration 4 burners 4 burners 144 B 97 74 B 94 65 50 3. 50 1. 65 1. 00 3. 50 1. 65 1. 00 333 l/h 157 l/h 95 l/h 254 g/h 120 g/h 73 g/h Rated consumption Reduced heat capacity kW 0. 60 0. 35 0. 30 0. 60 0. 35 0. 30 CATEGORY II2H3B/P Gas pressure mbar min. 25 20 30 35 Rated thermal flow rate (kW) 7. 80 7. 80 Total rated consumption 742 l/h 567 g/h Air required (m3) for burning 1 m3 of gas 9. 52 30. 94 HOW TO USE THE HOB WARNING Do not let the burner flame extend beyond the edge of the pan. IMPORTANT: WHEN THE HOB IS IN USE, THE ENTIRE HOB AREA MAY BECOME HOT. • To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting. [. . . ]