User manual WESTINGHOUSE W31501

[. . . ] nextgen-nt1503. book Page i Thursday, December 25, 2003 4:42 PM i nextgen-nt1503. book Page i Thursday, December 25, 2003 4:42 PM Preface About this Manual This manual is designed to assist you in setting up and using your LCD display. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. Copyright Copyright 2003. [. . . ] 9 nextgen-nt1503. book Page 10 Thursday, December 25, 2003 4:42 PM Getting to Know Your LCD Display 2. 8 Built-in Speakers The LCD display comes with a pair of built-in stereo speakers located at the front of the unit. 2. 9 Connecting the AC Power Adapter You must use the 100-240 VAC/60W power adapter that is included with the LCD display. Caution: · Make sure you have read and understood the safety notes before connecting the LCD display to the power adapter and electrical outlet. Do not use any other AC power adapter except the adapter that was included with your LCD display. Contact your dealer if you need a replacement adapter. · · 1 Connect the power cord to the AC adapter. 2 Plug the power cord into an electrical outlet. Contact your dealer or a qualified service technician if the plug does not fit into the outlet. AC 100~240V 3 Insert the small end of the adapter cord into the DC-in connector at the back of the LCD display. The power LED on the front panel glows orange. Power 10 nextgen-nt1503. book Page 11 Thursday, December 25, 2003 4:42 PM Getting to Know Your LCD Display 2. 10 Turning On the LCD Display 1 Press the Power key on the LCD ENGLISH DC 12V display control panel or remote control to turn the LCD display on. The power LED on the front panel glows green. 2 Press either Power key again to turn the LCD display off. The power LED on the front panel glows orange. 2. 11 Power Management System Your LCD display complies with the VESA DPMS power management proposal. The VESA DPMS proposal provides four phases of power saving modes by detecting the horizontal or vertical sync signal. When the LCD display is in power saving mode or detects an incorrect timing, the monitor screen becomes blank and the power LED indicator blinks green. 2. 12 Status LEDs The following table describes the LCD display status LEDs. Mode PC LED Blinking Green Blinking Green Meaning Power saving mode Over-range detected (the input signal is out of the range of the monitor). Normal Operation Normal Operation Signal is present No Signal is present Steady Green TV AV/SV/YPbPr Power Off Steady Green Green LED Orange LED LED off 11 nextgen-nt1503. book Page 12 Thursday, December 25, 2003 4:42 PM On-Screen Display 3 On-Screen Display This chapter explains the LCD display's On-Screen Display (OSD) and menus. If the computer is in a power saving mode, or is powered down, the OSD is inaccessible. Using the OSD you can adjust the contrast, brightness, OSD position, display timing, color temperature, stereo speaker volume, as well as set other OSD parameters. The OSD menus can be accessed using the remote control or the control panel on the right-hand side of the LCD display. 3. 1 OSD Menus To access the OSD, press the Menu button on the control panel or the Enter button on the remote control. In the OSD main menu the following submenus are available. Note: The V-Chip Menu is only available when using TV mode in North America (NTSC). 12 nextgen-nt1503. book Page 13 Thursday, December 25, 2003 4:42 PM On-Screen Display 3. 2 OSD Menu Controls ENGLISH The OSD can be operated using the control panel or the OSD buttons on the remote control. Control Panel Remote Control Description OSD Exit In OSD mode, use the control panel OSD Exit button SOURCE or the remote control to exit the OSD (from the Back button Main Menu) or to go back to a prior menu level (from a submenu). SOURCE MENU OSD Enter To choose an option from the OSD menu, select the option with the OSD Item Select buttons, then press the MENU button on the display's Control Panel or press the OSD on your Remote Control. Enter button OSD Item Select To navigate the OSD menus, press the Up or Down channel buttons on the display's control panel or the Function up or Function down OSD Function Arrows on your Remote Control Unit. OSD Value Adjust To adjust the value of a selected option, use or adjust buttons on the Remote the Control, or the or Volume buttons on the display's Control Panel. Press ­ to decrease the value. 13 nextgen-nt1503. book Page 14 Thursday, December 25, 2003 4:42 PM On-Screen Display 3. 3 OSD Options The following options are available once you have entered the submenus (Display, Video, Miscellaneous, Audio, and V-Chip). 3. 4 Display Menu Options The Display menu option enables you to configure the display for your LCD display. · VGA (computer) · TV (television) · SV (S-Video) · AV (composite) · YPbPr (Component) SUB enables you to select the picture in picture (PIP) signal source. The number layout is shown as follows: 1 4 7 2 5 8 3 6 9 · · · 14 nextgen-nt1503. book Page 15 Thursday, December 25, 2003 4:42 PM On-Screen Display 3. 5 Video Menu Options ENGLISH These options are used to configure the video image, captioning, and other items for your LCD display. [. . . ] For information on the V-Chip, refer to the FCC's Web site at: http://www. fcc. gov/vchip/. A list of the MPAA and TV ratings and their meanings is given in the following tables. For those under the age of 17 require accompanying parent or adult guardian. X is an older rating that unified with NC-17 but may be encoded in the data of older movies. [. . . ]