User manual WESTINGHOUSE LTV-27W7 HD

[. . . ] To ensure reliable operation of the LCD TV and to protect it from overheating, these openings must not be blocked or covered. · Do not block the openings by placing the LCD TV on a bed, sofa, rug or other similar surface. · Do not place the LCD TV in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer's instruction have been adhered to. Other Notices · Avoid exposing the LCD TV to direct sunlight or high temperatures. [. . . ] This equipment generates, uses, and can radiate radio frequency energy, and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the Westinghouse Service Center or an experienced radio/TV technician for assistance. FCC Warning To assure continued FCC compliance, the user must use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized changes or modifications not expressly approved by Westinghouse Digital will void the user's authority to operate this device. 5 INSTALLATION This User Manual covers models: LTV-27w7 HD, LTV-32w6 HD and LTV-37w2 HD English Package Contents Your product package includes: · Westinghouse LCD TV · Remote Control (with batteries) · Power Cord · Quick Connect Guide · User's Manual · Warranty Card Front View of the LCD TV Speakers IR receiver Rear View of the LCD TV 6 Side View of the LCD TV English SpineDesign Input connector Control keys Control Key MENU + VOL + CH INPUT 1. Power Turn OSD Menu ON/OFF Increase/Decrease sound volume or adjust a highlighted control while in the OSD Menu Channel up/down when input is TV or highlight a control while in the OSD Menu Select Active Video Input or choose a selection while in the OSD MENU Power ON/OFF 7 Input connector 1. S-Video Input Connect to a legacy video device such as a VCR or video game system. Video Input Connect the Composite Video to a legacy video device such as a VCR or video game system. Video & S-Video Audio Input (Right / Left) Connect an external audio source to this jack (Audio (R/L). Input : Scroll input source TV, HDTV, Video, S-Video, YPbPr1, YPbPr2, VGA, and HDMI. Scaling : Select Video Display format "STANDARD" or "FILL". DVI: No function Select DVI source input *For models with DVI input 26. Note: Before setting up favorite channel buttons, please make sure channel list is saved in TV. If not, auto scan to save a channel list in TV. English 10 Installation 1. Insert Remote Control Batteries English 1) Remove the battery cover. 2) Insert the batteries corresponding to (+) and (-) marks on the battery compartment. 3) Re-attach the battery cover. CAUTION: · Only use AAA batteries. This may result in cracking or leakage, which may pose a fire risk or lead to personal injury. Inserting the batteries incorrectly may result in cracking or leakage, which may pose a fire risk or lead to personal injury. · Dispose of used batteries in accordance with local laws and regulations. · When the remote control will not to be used for an extended period, remove the batteries. 11 Connect one or all of the following into the back of the LCD TV. IMPORTANT: Before beginning, make sure all devices are turned off. 2. [. . . ] Make sure the video cable connected to the LCD TV is tightly secured to the video output port on the back of the computer. If the other end of the video cable is not attached properly to the LCD TV, secure it tightly. If you are using a Macintosh computer older than G3, you need a Macintosh adapter. Check Source settings. Power is ON but No Screen Image · · · · Wrong or Abnormal Colors · · · · · If any colors (red, green, or blue) are missing, check the video cable to make sure it is connected securely. [. . . ]