User manual VIEWSONIC WPD-100

[. . . ] ViewSonic ® WPD-100 WirelessPresentationDongle - UserGuide ModelNo. :VS13789 ComplianceInformation ForU. S. A. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] It's recommended to keep this value untouched unless you know the effect of changing this value. You can drag the slider to set the threshold value, or input the value in the box located at right. It's recommended to keep this value untouched unless you know the effect of changing this value. ViewSonic WPD-100 19 To set authentication / encryption information for the access point. \ Encry. ' tab: Here are descriptions of every setup item: Item Name Description Authentication Select the authentication type of the wireless access point or wireless device you wish to connect. When you're adding a profile from an existing access point or wireless device, authentication type will be selected automatically, and please do not change it. Encryption Select the encryption type of the wireless access point or wireless device you wish to connect. When you're adding a profile from an existing access point or wireless device, the encryption type will be selected automatically, and please do not modify it. If encryption is not enabled, Preshared or you select `WEP' as encryption type, this field will be Key disabled and grayed out. WEP Key You can select key type (Hexadecimal or ASCII) and input WEP key here. If encryption is not enabled, or you select `WPA' as encryption type, this field will be disabled and grayed out. For Hexadecimal key, you can input number 0-9 and alphabet a-f; for example, `001122aabbcc'; For ASCII key, you can input number 0-9 and alphabet a-z; for example, mywepkey12345. ViewSonic WPD-100 20 Use 802. 1x The length of WEP key depends on the type of WEP key you selected. You can input 10 or 26 hexadecimal characters and 5 or 13 ASCII characters as WEP key. If the access point you wish to connect requires 802. 1x authentication, please click on `Use 802. 1x' box, then click `802. 1X' tab to set 802. 1x parameters. To set 802. 1x authentication for the access point. Please click `802. 1X' tab: Here are descriptions of every setup item: Description Select 802. 1x EAP method from dropdown menu. Please ask the administrator of the access point you wish to connect to select a correct EAP method. Tunnel Select 802. 1x tunnel authentication type from dropdown Authentication menu. Please ask the administrator of the access point you wish to connect to select a correct tunnel authentication method. This pull down menu is only available when authentication type you use is 'PEAP', `TLS / Smart Card', or 'TTLS'. When you use 'EAP-FAST' as authentication type, the protocol setting is always 'Generic Token Card' and can not be changed. You also need to select `Soft Token' or `Static Password' as password in `ID \ Password' setting. 'EAP Fast' authentication type also have a sub-menu to set EAP fast-specific parameters: Item Name EAP Method ViewSonic WPD-100 21 If you need to use protected authentication credential, check `Use protected authentication credential' box, and click `Import' to load . pac credential file; to remove a loaded credential file, click `Remove'. If you Resumption don't know if you should enable session resumption or not, please ask your 802. 1x authentication administrator. [. . . ] Add the MAC address you inputted in `MAC address' field to the list. Please select a MAC address from the list, then click `Delete' button to remove it. Delete all MAC addresses in the list. When you finish with setting and want to save changes, click `Apply' button. ViewSonic WPD-100 44 3-4 Connection Table If you want to see the list of all wireless clients connected to this access point, please select `Mac Table' tab from the utility. Here are descriptions of every field: Item Name MAC Address AID Power Saving Mode Status Description Displays the MAC address of this wireless client. Displays the capability of power-saving function of this wireless client. [. . . ]