User manual VIEWSONIC VA2431W

[. . . ] ViewSonic VA2431w/VA2431wm LCD Display ® IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// www. viewsonic. com in English, or in specific languages using the Regional selection box in the upper right corner of our website. "Antes de operar su equipo lea cuidadosamente las instrucciones en este manual" Model No. : VS12996 Contents Compliance Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Four screws attaching the base ViewSonic VA2431w/VA2431wm 7 Using the LCD Display Setting the Timing Mode Setting the timing mode is important for maximizing the quality of the screen image and minimizing eye strain. The timing mode consists of the resolution (example 1920 x 1080) and refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the OSD (On-screen Display) controls to adjust the screen image. For the best picture quality set your LCD display timing mode to: VESA 1920 x 1080 @ 60Hz. Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the resolution. Set the refresh rate: See your graphic card's user guide for instructions. WARNING: Do not set the graphics card in your computer to exceed the maximum refresh rate of 75Hz; doing so may result in permanent damage to your LCD display. OSD and Power Lock Settings · OSD Lock: Press and hold [1] and the up arrow for 10 seconds. If any buttons are pressed the message OSD Locked will display for 3 seconds. · OSD Unlock: Press and hold [1] and the up arrow again for 10 seconds. · Power Button Lock: Press and hold [1] and the down arrow for 10 seconds. If the power button is pressed the message Power Button Locked will display for 3 seconds. With or without this setting, after a power failure, your LCD display's power will automatically turn ON when power is restored. · Power Button Unlock: Press and hold [1] and the down arrow again for 10 seconds. ViewSonic VA2431w/VA2431wm 8 Adjusting the Screen Image Use the buttons on the front control panel to display and adjust the OSD controls which display on the screen. The OSD controls are explained at the top of the next page and are defined in "Main Menu Controls" on page 11. VA2431wm Main Menu with OSD controls Front Control Panel shown below in detail Displays the control screen for the highlighted control. Also a shortcut to toggle analog and digital connection. Power light Blue = ON Orange = Power Saving Standby Power On/Off Scrolls through menu options and adjusts the displayed control. Audio Adjust ( ) / Contrast ( ) Displays the Main Menu or exits the control screen and saves adjustments. ViewSonic VA2431w/VA2431wm 9 VA2431w Main Menu with OSD controls Front Control Panel shown below in detail Displays the control screen for the highlighted control. Also a shortcut to toggle analog and digital connection. Power light Blue = ON Orange = Power Saving Standby Power On/Off Scrolls through menu options and adjusts the displayed control. Brightness ( ) / Contrast ( ) Displays the Main Menu or exits the control screen and saves adjustments. ViewSonic VA2431w/VA2431wm 10 Do the following to adjust the display setting: 1. To display the Main Menu, press button [1]. VA2431wm VA2431w NOTE: All OSD menus and adjustment screens disappear automatically after about 15 seconds. To select a control to adjust, press or to scroll up or down in the Main Menu. A control screen like the one shown below appears. The line at the bottom of the screen shows the current functions of buttons 1 and 2: Exit or select the Brightness control. 4. [. . . ] Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, unauthorized attempted repair, or failure to follow instructions supplied with the product. Causes external to the product, such as electrical power fluctuations or failure. Any product exhibiting a condition commonly known as "image burn-in" which results when a static image is displayed on the product for an extended period of time. How to get service: For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). [. . . ]