User manual VIEWSONIC PJ510

[. . . ] PJ510 User Guide Contents For Your Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · NORMAL is the mode for images with a lot of motions like movies, and STILL IMAGE is the mode for images with few motions or completely still ones like slides. · When this function performs, the VIDEO NR function is ineffective COMPONENT VIDEO FRAME LOCK 3D-YCS 25 ViewSonic PJ510 INPUT Menu(Continued) Item VIDEO NR Description Select a Noise Reduction Mode: HIGH ( ) ( ) MIDDLE ( ) ( ) LOW · This function performs only at a VIDEO input or a S-VIDEO input. At a VIDEO input of NTSC 3. 58, this function performs only when the TURN OFF is selected under the 3D-YCS. · When the HIGH, the MIDDLE or the LOW is selected, the noise on screen is reduced according to each mode. · When this function is excessive, it may cause a certain degradation of the picture. Select the Progressive Mode: TV ( ) ( ) FILM ( ) ( ) TURN OFF · This function performs only at an interlaced signal of a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input of 525i or 625i signal. The FILM mode is adaptable to the 3-2 PullDown system to the conversion. · This function may cause a certain degradation of the picture. Display the Information: Pressing the ( ) or the ENTER button performs this function. · Use this function when you want the information about the current input (ex. the resolution and the vertical frequency at a RGB input, the signal type of a video input) and setting states of the COMPONENT, the VIDEO and the FLAME LOCK. Select the S2-ASPECT Mode: TURN ON ( ) ( ) TURN OFF · This function performs only at a S-VIDEO input. · When the TURN ON is selected, an S2-Video signal can be identified and the optimum aspect ratio is automatically selected. · When the ASPECT button of the remote control is used or the ASPECT item of the MAIN menu is operated, the S2-ASPECT mode will be switched to the TURN OFF automatically. Reset the INPUT Menu Items: Selecting the EXECUTE performs this function. EXECUTE ( ) CANCEL · The items of the INPUT menu are collectively returned to the initial setting. Note that the INFORMATION item is not reset. PROGRESSIVE INFORMATION S2-ASPECT RESET ViewSonic PJ510 26 AUTO Menu With the AUTO menu, the items shown in the Table below can be performed. Perform each operation in accordance with the instructions in the table below. Item ADJUST Description Automatically Adjust the Picture: Pressing the ( ) or the ENTER button performs this function At a RGB input: · V POSITION, H POSITION, H PHASE and HSIZE are automatically adjusted. At a VIDEO input or S-VIDEO input: · This function performs only when the AUTO is selected under the VIDEO item of the INPUT menu. For a COMPONENT VIDEO input, although this function is ineffective, the signal type is identified automatically even if the AUTO is not selected. · This function automatically selects the optimum mode for the input signal. However, it may not work well at a PAL60 signal and some other signals. [. . . ] THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO AN APPROPRIATE SOCKET. If a new plug is to be fitted, please observe the wiring code as shown below. IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Green-and-Yellow: Earth Blue: Neutral Brown: Live If the coloured wires of the mains lead of this appliance do not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. [. . . ]