User manual VDO DAYTON MS 5500

[. . . ] CONTENTS GENERAL INFORMATION Explanation of symbols 4 For your safety! 6 Maintenance and care 6 Functions of your navigation system 6 Range of functions 6 System expansion 7 Distance indications 7 Operating restrictions (country-specific) 7 GPS reception 7 Start-up characteristics 7 Automatic route re-calculation 7 Areas with limited road information 8 Switching on / off 8 Remote control 8 Stand-by 10 Inserting/changing the map DVD/CD 10 C-IQ - Your key to map, traffic and travel information 11 Activation options 11 Reading the Navi ID 12 Code input 12 C-IQ SMS list 13 My C-IQ 13 Prepaid C-IQ 13 Preview 14 Configuration 14 C-IQ Service 15 Screen menu types 15 Popup menu 15 Pull-down menu (functions list) 16 List screen 16 Settings adjusting the navigation system 17 Day / night colours 17 Screen configuration 18 Message selection 19 Route criteria 19 Dynamic route 20 Speed warning 21 Remote control 22 Favourite function 22 General Settings 23 Language 23 Audible settings 23 Measuring units 24 1 CONTENTS Device configuration Shut-Down timer System configuration Info Points Default settings 25 26 26 27 28 NAVIGATION Destination input Direct address input Function "List" Special destinations Points of interest Junction All streets (Quick Access) Address book (see also chapter Address book) Destination map Via points (intermediate destinations) Stop guidance Travel info Points of interest Travel symbols Screen displays Guidance display Map display Split screen Guidance in non-digitised areas Guidance in partly digitised areas Audible messages Plan Alternative Route TMC traffic information Pay TMC In the map display On the guidance display TMC detail information Graphic display of a road obstruction Bypassing a road obstruction Concurrent dynamic route guidance TMC symbols "Info" menu The address book Store addresses Delete address Delete previous destinations Store vehicle position in address book Retrieve address from the destination memory 30 30 31 31 31 32 32 33 33 34 35 35 36 37 38 38 39 39 40 40 40 40 41 42 42 43 43 44 44 45 46 47 48 48 48 48 49 49 2 CONTENTS TELEPHONE CI 3000 CIX 3000 Blue Linking of mobile phone with CIX 3000 Blue Driver software for the CI 3000 Loading phone book Telephone functions Calling Volume of call Dialling Dialling via numeric buttons Call list Calls from the phone book Retrieving an entry from the phone book Deleting an entry Adding an entry (only on SIM card) SMS (Short Message Service) Receiving SMS messages Reading SMS messages Writing SMS messages Sending SMS messages Direct dialling of displayed phone numbers Telephone Settings Phone Info Phone book Storing a mailbox no SW download Bluetooth 50 50 51 51 52 53 54 54 54 54 54 55 55 56 56 56 57 57 58 58 58 59 59 59 60 60 60 USEFUL EXTRAS Trip computer 61 Emergency 62 Entering an assistance number 63 TROUBLESHOOTING Troubleshooting 64 3 GENERAL INFORMATION Explanation of symbols The following symbols are used in this manual: !This symbol is used to indicate safety instructions and warnings. These contain important information for the safe use of the unit. Failure to observe this information may result in a risk of damage or injury. [. . . ] Press the OK button. 32 NAVIGATION Address book (see also chapter Address book) If the desired destination address is already in the address book, or happens to be one of the last 20 destinations entered, the address can easily be used as a destination address: u In the "Navigation" menu select the function "Address book", press the OK button. u Select "Retrieve address", press the OK button. u Select the address book category, or the destination memory containing the last 20 destinations by means of "Prev. Press the OK button. Choose "Quit" from the list or press the left cursor button to leave the list display without selecting one of the list entries. If maps from different providers are used it may be necessary to adapt the stored addresses. Destination map The destination map can be used to enter a destination by means of: Cursor Co-ordinates Cursor If the destination is not in the vicinity of the vehicle location, first enter the destination as accurately as possible using the keypad (see Direct address input). u In the "Navigation" menu select the option "Destination map", or u press a cursor button if the map is already being displayed. The cursor marks the current vehicle location if no destination data has been entered. u Use the cursor buttons to move the cursor. u Press the OK button, select "Store", and press the OK button again, so that the system accepts the position as a destination. t First select a large scale for an approximate destination definition. Then choose a smaller scale to mark the destination accurately with the cursor. Destinations which are not in the digitised map area can also be selected. Ensure that correct side of the road is selected when targeting a destination on motorways. 33 NAVIGATION Co-ordinates u Select "Destination map" under "Navigation". Press the OK button. u Select "Co-ordinates", and press the OK button. u Select "Longitude" or "Latitude", press the OK button. u Define each digit with the cursor buttons on the remote control and confirm with OK. Should you wish to skip a digit, press the OK button. u Select "Set co-ordinates", press the OK button. u To start navigation press the OK button, select "Return", select "Guidance" and press the OK button again. Via points (intermediate destinations) Should you wish to drive to other locations on your way to your destination, these can be entered as via points. The navigation system then plans the route to include the via points according to their order of entry before the destination address is reached. Once a via point has been passed it is automatically deleted from the list. A maximum of 25 via points can be stored. u In the "Navigation" menu select the function "Via points". You can enter the via points in the same way as destination addresses (see above sections). If a via point is active, all route information such as distance or travel time relates to that via point. 34 NAVIGATION Storing a via point u Select "Store via point" and press the OK button. Deleting via points u Select "Delete via point" and press the OK button. A list of the stored via points appears. u Select the via point to be deleted and press the OK button. A popup menu with the entry appears. u Select "Delete" and press the OK button, if you wish to delete the displayed via point from memory. u Select "Quit" and press the OK button, if you do not wish to delete it. [. . . ] Screen switches off under excessive temperature. After the ignition has been switched off, the last menu remains visible on the screen. System does not react to actuation of the buttons if remote control is not in its holder. System reacts very slowly to inputs, or takes a long time to respond "Guidance" cannot be selected in "Navigation" menu Batteries are empty: Replace the batteries in the remote control, or install the remote control in its holder. You are located in an extremely densely digitised area. The system requires more time to read large data quantities. Ensure that you have entered a destination address. 64 TROUBLESHOOTING Symptoms System fails to plan route despite destination address being entered. [. . . ]