User manual VDO DAYTON MS 2010

[. . . ] MS 2010 MS 2110 Traffic Quick Start Guide Erste Schritte und wichtige Hinweise First Steps and Important Notes Premiers pas et instructions importantes Primeros pasos y advertencia importante Primi passi e avviso importante Primeiros passos e avisos importantes Aan de slag en belangrijke aanwijzingen Komma igång och viktiga anvisningar Kom i gang og viktige anvisningar Portable Navigation Device © 05/2006 Siemens VDO Trading GmbH Dansk Svenska Nederlands Português Italiano Español Français English Deutsch Contents · General Instructions Contents 21 General Instructions . 40 Safety Advice and Important Information Before you start to mount and use this navigation system, please familiarise yourself with its various components and functions. Furthermore, please read through the safety instructions carefully to avoid causing injury to yourself and/or other road users. The use of the navigation system does not under any circumstances release the driver from his/her personal responsibility. [. . . ] You can also refresh your route or allow the system to take traffic information into consideration (only for traffic product version). Simulation In this menu it is possible to simulate your route. For example set start location and the navigation system can simulate driving to your desired destination and back. TMC TMC or Traffic Message Channel allows you to obtain traffic information (only for traffic product version). During navigation the system regularly accesses the latest TMC traffic information in the background; provided that this information is available in the part of the country you are in. Alert points Alert points can give visible and audible notifications. Position & speed In this menu you can change the current position. Select map This opens a selection screen where you can choose from the installed maps. System ID Tap this option to show product and Map database versions. What you select here can be changed at any time. Updates can change the structure of the menu. Toolbar The toolbar is a shortcut to different functions and information (e. g. You can open and close the Toolbar by tapping the VDO Dayton logo (bottom right of screen). 30 GPS and TMC GPS Status and Quality When you switch on the device for the first time, it can take several minutes for the GPS reception to reach a sufficient level and to determine your current position. If you are unable to obtain a sufficient GPS signal, please read the Troubleshooting chapter for suggestions on solving the problem. If necessary, you can pivot the GPS antenna upwards to improve the reception. If you are using the navigation system in an inner-city area, it may take longer to load maps and navigation information. This is due to the large number of roads and additional information (e. g. Furthermore it may take longer to establish the GPS reception if you have just driven out of an underground car park or another type of building where GPS signals are blocked. The GPS reception can be checked by doing the following Check the GPS status in the status bar. In case the status bar does not show the GPS status: tap on a status bar element and select GPS status from the list. The amount of tracked GPS satellites is shown. The quality of the GPS signal is indicated by the shape and colour of the check mark: Red Yellow Yellow Green No reception Initializing or insufficient signal quality, less than 3 satellites found Sufficient signal quality, but not very accurate Good signal quality GPS and TMC TMC Status and Quality (only for traffic product version) 31 Using TMC offers you an additional function to allow you to dynamically avoid traffic jam. During navigation the system regularly accesses the latest TMC traffic information in the background; provided that this information is available in the part of the country you are in. TMC is switched On, the traffic information is known and send by the provider, the information can be received. When you set TMC On and there is no reception, a red checkmark is shown. When you receive TMC, the name of the provider is shown green in the status bar. If TMC is switched Off, no provider is shown and a narrow line is visible. When TMC is switched On and you receive traffic information, the status bar also visualises the delay time. This is indicated by the colour of the hourglass: Red There is TMC information and delay time Green There is TMC information but no delay time Grey TMC is not available or switched off (only for traffic product version) When TMC is switched On and there is a traffic jam on your route, a pop up icon appears in the left corner on the map display screen. TMC-antenna To receive TMC messages, the antenna provided with the package must be connected to the traffic system version. The antenna with suckers should be placed on the windscreen and fixed. 32 Navigation Navigation The purpose of the navigation system is to guide you from your present location to your desired destination. The navigation function automatically determines your present location using the GPS signal. [. . . ] · Tap the desired folder in the browser screen. The title selection screen appears. · Next, tap the desired title; the Music menu appears and the chosen title starts to play. · Tap the Back button to return to the previous menu. 38 Multimedia Tap the JPEG viewer button. Viewing Pictures ­ The JPEG Viewer The JPEG viewer's JPEG menu appears. Using the symbols in the menu, you can perform the following functions: 1 Jump to previous picture 2 Jump to next picture 3 Switch to previous folder 4 Switch to next folder 5 Start slide show 6 If you tap on the picture, the image is displayed in full screen mode. [. . . ]