User manual VDO DAYTON MM 2700

[. . . ] Safety instructions and warnings contain important information for the safe use of the unit. Failure to observe this information may result in material damage or personal injury. Therefore, please observe this information with particular care. A Safety instructions For safety reasons, the driver should not watch TV/DVD or similar when driving. Please note that it is illegal in certain countries to watch or to operate a TV/DVD or similar device when driving. A A A A Only use the monitor for its intended purpose. If an electronic reverse monitoring camera is used, ensure that this does not cause a hazard. [. . . ] MIRROR: Mirrors the display contents on the vertical axis (useful, for instance, if a reversing camera is connected). UP/DOWN: Mirrors the display contents on the horizontal axis (if the monitor is installed overhead). DEFAULT: Resets all settings to the factory values. 6 INSTALLATION INSTRUCTIONS IMPORTANT INFORMATION Fire hazard: when drilling, take care not to damage concealed wiring harnesses, the fuel tank or fuel lines. A A A A A A A A A A A A A The unit must only be installed by trained personnel. Observe automotive industry quality standards and the relevant local statutory regulations. Never drill into supporting or safety-relevant body parts. It is essential to observe the following when installing components in the passenger compartment: Ensure that the driver has a clear all-round view. Increased risk of injury in the event of an accident. Do not install components in the inflation range of the airbag or in areas where the head may knock against them. Only install the unit in vehicles with a 12-V on-board voltage; connect negative pole to earth. heavy goods vehicles, buses) results in a risk of malfunction, damage and fire. Do not use test lamps to test the voltage, since excessively high currents could damage/ destroy electronic components. In order to ensure perfect installation, use only the original components supplied. Do not install the unit in positions where it is exposed to high temperatures, dust, dirt or excessive vibration (e. g. due to direct sunlight or heating vents). Scope of delivery Check the scope of delivery for completeness before starting work. The complete installation kit contains: 1 MM 2700 with 5 m connecting cable 1 Installation bracket for headrest integration + 1 disassembly tool 1 Infrared remote control 1 Stereo headphone (3. 5-mm jack) 1 Installation and operating instructions Report faulty components to the Service department and notify any damage to the deliverer (forwarder, package service, post office). Technical data, design and scope of delivery may vary slightly due to product updating. 7 English INSTALLATION INSTRUCTIONS Connection 1. Connect the mini-DIN plug of the connecting cable to the AV1 socket at the rear of the monitor. Connect the RCA/cinch plug to the video source (yellow: video; red: audio R; white: audio L). s Permanent installation For a permanent installation, the plug for the cigarette lighter can be removed and the monitor can be supplied with power via the connecting cables (red and black). Cable colour Red Black Connection +12 V ignition positive / accessory contact Battery negative / earth Before starting work, disconnect the earth lead from the negative terminal of the vehicle battery in order to prevent short circuits. At the same time, follow the vehicle manufacturer's safety instructions (alarm system, airbag, immobiliser, radio coding, etc. ). A A A The fuse of the red connecting cable (+ 12 V) must not be removed. The + 12 V ignition positive / accessory contact must be designed for a current of at least 2 A. Only connect electrical signals to suitable connecting points in the vehicle. s Remote-control output If you use a VDO Dayton DV 6100 / DV 6200 DVD player, you can connect the 3. 5-mm jack on the monitor connecting cable to the remote-control input on the DVD player. The remotecontrol signals will then be received by the monitor and forwarded to the DVD player. [. . . ] in green" setting in the "Settings" menu of the navigation computer. (Please contact your authorised dealer if you have any further queries). · Connect the earth lead of the monitor to another suitable earthed point to avoid earth loops (e. g. connection point of the video source). The hue of the navigation display appears "corrupted". The picture appears slightly distorted. Hotlines are available in many countries to handle queries regarding our multimedia systems. [. . . ]