User manual VDO DAYTON CR 223

[. . . ] Please read carefully the instruction manual and use the device as intended. CONTENTS PAGE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Connect pin A5 to the power supply for an electronic antenna or the control wire for the relay of an automatic motorised antenna. [. . . ] 1 Do not switch off the set when the display shows "WAIT" (The waiting period will start all over again when the set is switched on. )!3 Enter the correct code as described in "Entering the code". The waiting period doubled each time an incorrect code is entered (1 minute, 2 minutes, 4 minutes, etc. . . ). key pressed, switch on pressed until you hear a 13 . . . . . . . . . . . . . . . CD opening / Cassette opening * Depending on version 6 6 2004-4-30, 14:38 2 Enter the code as described in "Entering the code". You will hear two beeps indicating that the Code Protection has been deactivated. If an incorrect code is entered, you have to follow the same procedure as described in "Entering the code". Please make sure you can still hear the traffic (horns, sirens. . . . . . . . ) MUTE (Silence) Short press key to mute or cancel the mute (silence). Note : The silence period may be interrupted by ALARM announcement or traffic announcement messages (if TA is switched on). SOUND Whether you listen to Jazz, Vocal, Pop, Classic or Rock music, the SOUND button is the perfect setting for your choice. · Press SOUND then the sound button to select BASS-Treb for your own sound style, or adjust the settings with the volume up/down buttons to select one of the pre define sound styles: - BASS-TRE : Your own settings of bass and treble. - FLAT: Original - JAZZ: Jazz music - VOCAL : Speech - POP : Pop music - CLASSIC : Classical music - ROCK : Rock music AUDIO SETTING · Press SOUND to select desired audio mode. · Adjust the settings with the volume up/down buttons: - Sound style (BASS-TRE, FLAT, JAZZ, VOCAL, POP, CLASSIC, ROCK) - BASS (low notes) - TREBLE (high notes) - BALANCE (left-right) - FADER (rear-front) - LOUD (OFF, LOW, MID, HIGH) · Press the volume button to adjust the selected audio mode. Adjustment of Bass and Treble setting is only possible when BASS-TRE is selected as the sound style. · While keeping the key pressed, switch on the set. Keep the pressed until the display shows "CODE" and you hear a beep. IF THE SET HAS TO BE SENT FOR REPAIR · Deactivate the Code Protection(as described above), or Write the protection code on a label and attach it to the set. IDENTIFICATION NUMBER This set has an identification number (stated on the 'Security card'). Show this card as a proof of ownership, when the set is stolen or when requesting service. · Do not keep the 'Security Card' in your car. * Depending on version 7 7 2004-4-30, 14:38 *SOURCE · Press SOURCE to select the desired source : - TUNER - CD* · Products with cassette mechanism will change source to cassette only when a tape is inserted. RADIO WAVEBAND · Press BAND to select the desired band : Automatically storing stations (AUTOSTORE) You can automatically store 5 strongest FM stations on the FM AST band or 5 strongest MW (AM) stations on the MW(AM) AST band. When you use Auto Store, the new stations replace any stations previously stored in the FM AST band or the MW(AM) AST band. - When it has finished, you hear a beep followed by the station stored on preset 1. - Sometimes it may not be possible to find 5 stations. RADIO DATA SYSTEM (RDS) ON FM AUTOMATIC SEARCH Use search tuning to automatically search for a station. [. . . ] · The tuned station becomes too weak to enable the reception of Traffic Announcements. · If the TA mode is switched on, search tuning only selects stations which enable the reception of Traffic Announcements. Cassette Display shows 'TAPE ERR'. Tape Slack · Check and make sure any slack in the tape is taken up before inserting the tape into the unit. A loose tape can get caught in the mechanism and cause damage to the unit and tape itself. [. . . ]