User manual VDO DAYTON CIX 3000 BLUE

[. . . ] 1 1 CIX 3000 Blue Bluetooth hands-free terminal 2 4 self-tapping screws 4. 2 x 16 mm 3 Vehicle network cable 4 Installation and operating instructions 5 Loudspeaker 6 Microphone 7 Infrared receiver 8 Infrared remote control 9 2 connecting plates 0 2 insulation piercing connectors/clamping connectors 5 English INSTALLATION INSTRUCTIONS Recommended installation locations, Fig. 2 s CIX 3000 Blue The CIX 3000 Blue should be installed in a location that is not electrically isolated (e. g. not beneath/behind sheet metal parts, in the luggage compartment) in order to ensure that the radio link to the mobile phone is not obstructed, e. g. If possible, the aerial slot should point towards the vehicle interior. [. . . ] when an attempt is made to establish a link or if the system is reset). Checking the vehicle functions Check the safety-relevant vehicle functions only when the vehicle is stationary, or moving at low speed. Brake system, alarm system, lighting system, immobiliser, speedometer, on-board computer, radio (coding) and hi-fi system, clock. A Service For up-to-date information and a compatibility list of the mobile phones supported, visit our website: www. vdodayton. com or contact a VDO Dayton dealer. Subject to technical modifications and errors. 9 English OPERATING INSTRUCTIONS Notes on operating instructions The following reading aids are used to simplify these operating instructions: asks you to perform an action. provides extra info. identifies a list. Safety instructions and warnings contain important information for the safe use of the unit. Failure to observe this information may result in a risk of damage or injury. Therefore, please observe this information with particular care. A Notes for mobile phones Some functions (e. g. starting of speech recognition) are not supported by all mobile phones. We cannot guarantee that all functions described will be supported by all mobile phones with Bluetooth. Initiating mobile phone speech recognition (depends on the mobile phone) Automatic mute of car radio Function The CIX 3000 Blue Bluetooth hands-free terminal offers a variety of options for installing a hands-free unit in your vehicle with minimum effort - you do not even need a cable for the mobile phone. Depending on the system configuration, you can control the basic functions of the mobile phone either using the IR remote control provided or - in conjunction with the CI 3000 - via a VDO Dayton navigation system. Audio playback is via the loudspeaker provided or via an optional accessory cable on VDO Dayton radios and radio navigation systems or other radio systems with telephone input. *) A list of all mobile phones supported can be found at www. vdodayton. com. 11 English OPERATING INSTRUCTIONS Basic functions s Selecting the Bluetooth profile Switch on the ignition to activate the hands-free terminal. Press the p and H buttons on the remote control to toggle between the "headset" and "hands-free" Bluetooth profiles. An audible signal confirms that the profile has changed and will remain active until the next change: Hands-free profile activated: 3 high tones Headset profile activated: 3 low tones Important note: We recommend that you use the hands-free profile if it is supported by your mobile phone. This profile was developed specifically for use with hands-free units (e. g. If you are using the headset profile, the range of functions supported will vary depending on the mobile phone. See section "Making and receiving calls with the headset profile". s Link between the mobile phone and the CIX 3000 Blue ("pairing" mode) In order to be able to use the mobile phone with the CIX 3000 Blue hands-free terminal, the terminal must be logged onto the CIX 3000 Blue. If, when the Bluetooth function is activated, a number of the telephones logged on are present, the telephone logged on first always has access to the CIX 3000 Blue. Press the 2 and 8 buttons on the remote control at the same time to activate registration mode. The CIX 3000 Blue will now wait for a Bluetooth mobile phone to log on. Next, activate the "Search for Bluetooth devices" on the mobile phone to establish the connection to the Bluetooth hands-free terminal. More detailed information about registering Bluetooth devices on your mobile phone can be found in the mobile phone operating instructions. Whilst the link is being established, you will be prompted to enter a Bluetooth PIN. [. . . ] The CIX 3000 Blue has switched to standby mode (Bluetooth connection off). · Install the microphone away from air nozzles and do not attach it to metal surfaces. · Select the "hands-free" profile to ensure optimum echo and noise suppression. · Select the "hands-free" profile to ensure the availability of all functions on the CIX 3000 Blue and your mobile phone. [. . . ]