User manual VDO DAYTON CD 2100

[. . . ] INSTALLATION If your car is equipped with ISO connectors, simply insert them in connectors of the car radio. If not, you can use an adaptor cable (Refer to the table on the separate installation card). Ensure all cables are installed so that they cannot be damaged by sharp edges or moving parts. · Blue lead A5 (Electronic/Motor Aerial) : PREPARATION Voltage and polarity: The set must be connected to a 12V car battery with negative terminal to earth (car chassis). Installation in vehicles not fulfilling these requirements could result in malfunction, damage or fire. [. . . ] DEMONSTRATION MODE In this mode, the display shows the main features of the set. SWITCHING ON DEMO MODE While keeping the DISPLAY key pressed, switch on the set. The set remains in the demonstration mode, even if you switch the set off and then on again. Follow the same procedure as 'SWITCHING ON DEMO MODE'. If speed warning is activated, flag ' ' turn on. To change the recorded speed, see 'STORE A SPEED'. * Depending on version 9 AUDIO ADJUSTMENT ON/OFF · Switch the set on or off : You can use the set even when the car ignition is switched off. VOLUME Please make sure you can still hear the traffic (horns, sirens. . . . . . . . ) · Adjust the volume : MUTE (Silence) : · Mute the set or cancel the mute : The silent period may be interrupted by traffic announcements (if TA/NEWS is switched on). SOURCE · Select the desired source : SOUND · Select one of the pre-defined sound styles: Radio Cassette/CD player* CD Changer * (if connected) Phone in (if connected) and if option is selected in Initial Settings and a call is active. Useful tips Set does not function. · Check fuse (set and car) and connections ­ BASS-TRE : Your own settings of bass and treble. ­ FLAT : Mid-positions of bass and treble ­ JAZZ: Jazz music ­ VOCAL : Speech ­ POP: Pop music ­ CLASSIC : Classic music ­ ROCK : Rock music ­ These settings are memorised for each source (Radio, Cassette/CD player* and CD changer *). SELECT · Select the desired audio mode : Set functions but no sound?Set mutes when you drive or display shows 'TEL CALL', but no car telephone is connected to the set. · See INITIAL SETTINGS; select Option 'TEL' and set Choice to 'NO' . Set mutes when you drive or display shows 'TEL CALL', but the car telephone is not in used. · See INITIAL SETTINGS; select Option 'PHONE' and set Choice to 'LO' or 'HI' according to phone type. Set mutes when you used the car telephone, display shows 'TEL CALL', but you may still like to listen to the radio. · To restore the same volume level ­ BASS (low notes), TREBLE (high notes), BALANCE (left-right), FADER (rear-front). · Adjust the selected audio mode. After 5 seconds the display goes back to the last mode of operation. LOUDNESS This option dynamically amplifies the high and low notes so as to improve the sound output at low volume levels. Display shows 'TOO HOT' and the sound from the speakers is reduced. · A built-in safety circuit prevents the temperature in the set from exceeding a certain level. · Wait until 'TOO HOT' disappears from the display before increasing the volume. * Depending on version 10 Useful tips Detachable front of set feels warm?Infrared remote control does not function (optional) · If the weather is cold, there may be some condensation on the infrared sensor. [. . . ] FAST BACKWARD / FORWARD To quickly move through the disc · Backwards : · If a disc is already inserted : Select CD as SOURCE : · Forward : Playback starts. ­ The display shows the track number, elapsed playing time during playback. CD PLAYBACK (CD Changer*, if connected) · You can only connect the following CD changer with a digital output to this set : - CH0400 or CH0600 or CH1000 · Check that the magazine is loaded with discs and inserted in the CD changer: · Select CD changer as SOURCE : ­ Normal playback resumes when you release the key. SCAN TRACK The scan function enables you to listen to the first few seconds of each track. [. . . ]