User manual UPM WS2635

[. . . ] Insert two 1. 5V AAA batteries (included) into the battery compartment. Make sure the battery is inserted in the correct polarities as marked. The wrong polarity may result in short-circuits and damage to the Remote Transmitter. Replace the battery cover and screw. C C WEATHER STA TION WS2635 WALL MOUNT HOLDER LOCAL 1 2 3 4 MAXRF MIN THERMO 1234 LOCAL RF THERMO 1 FIGURE 1 Quick Start Setting the Transmitter WT260 LCD DISPLAY C C Use the same method as in clock setting to set the alarm time. [. . . ] (Snooze Function: If SNOOZE is pressed, the alarm will stop and sound again after 5 minutes. ) Operation and Display of Weather Station The LCD display of the Weather Station can be divided into 2 sections: The Upper Display Area and the Lower Display Area. Various clock functions are arranged in a circular pattern as shown below and are displayed on the Upper Display Area: Clock Alarm Kitchen Countdown Timer Clock . . . LOCAL MODE RF THERMO 1 SET ST/SP CHANNEL SNOOZE KEYS SET RESET BATTERY COVER BATTERY COMPARTMENT SCREW FOR BATTERY COVER Remove the battery cover screw of WT260. Open the cover and install 2 AAA batteries included according to the polarity marked. If you have only one transmitter, just wait for 12 seconds to accept this value. If you want the display in °F , press SET button at the back ONCE. If you have more than 1 transmitter, repeat the above for the other transmitter while selecting different Device code. Features of Remote Transmitter WT260 / WT260H Temperature Display in ºC or ºF Humidity Display (WT260H only) Compact size with Wall-mount holder Drip-proof design Transmit temperature and humidity (WT260H only) data by RF Technology to the Weather Station 5 Press MODE or /CHANNEL to increase or decrease its value. For the setting of Second, it can be set to "00" of the present minute by pressing CHANNEL or "00" of the next minute by pressing MODE . To change between 12 and 24 hour display, press ST/SP while setting clock. Press SET while Second is flashing to end the clock setting. Kitchen Countdown Timer To set the Countdown Timer press SET in Countdown Timer , mode. (Figure 4) C C To move from one mode to the other, press the MODE key. If the remote temperature display starts to flash, it indicates that the signal is temporary lost. This may be due to interference from nearby electrical appliances or environment. You can wait for a while to see if the flashing will stop because most interference is temporary. Sometimes the signal received is too weak and you can try to move the Weather Station and/or Transmitter to a different location to have better reception of the signals. Flashing will stop once the signal is received by the Weather Station again. However, if flashing does not stop, it indicates that the Weather Station cannot receive signals from the Transmitter and the Learn function must be activated again. C C If the remote temperature is not displayed on the Weather Station within 2 minutes after setting up, it is advised to relocate the positions of the devices or move the devices away from other electrical appliances as they may be subject to interference. If the problem persists, reset both devices again. Maintenance To avoid damage to the device, do not place the Weather Station or Transmitter in places where there is a risk of vibration or shock. For both the Weather Station and the Transmitter, use batteries of recommended size only. Transmitter WT260 : 2 x1. 5V AAA size batteries (or equivalent) Detectable Temperature Range : From - 30ºC to +70ºC (Resolution: 1ºC [Below - 10ºC]; 0. 1ºC [Above - 10ºC]) Detectable Humidity Range : From 15% to 95% (Resolution 1%) (For WT260H only) : 433. 92MHz Transmission Frequency Transmission Range : 40 Meters in open area Battery Type Low Battery Indication 1 RF THERMO 2 FIGURE 11 4. Right box - Press CHANNEL display modes: Auto CH. 1 CH. 2 to scroll through the following CH. 4 Auto CH. 3 Weather Station - indicated by the flashing "LOCAL" symbol below the Left box. Remote Transmitter - indicated by the flashing Channel Number on the Weather Station; and "Lo bat" also appears periodically on the display of the Transmitter as in Figure 13. Error/ Abnormal Display When there is an abnormal display or malfunction (e. g. , the Weather Station is unable to learn and display the data from the Transmitter(s)), replace the batteries and re-set both the Weather Station and the Transmitter(s) again. Selecting the Temperature/ Humidity Display Combinations on Weather Station 1. [. . . ] Remote Transmitter - indicated by the flashing Channel Number on the Weather Station; and "Lo bat" also appears periodically on the display of the Transmitter as in Figure 13. Error/ Abnormal Display When there is an abnormal display or malfunction (e. g. , the Weather Station is unable to learn and display the data from the Transmitter(s)), replace the batteries and re-set both the Weather Station and the Transmitter(s) again. Selecting the Temperature/ Humidity Display Combinations on Weather Station 1. Initially, local data is displayed on the left display box and remote data is displayed on the right. Left box - Press and hold CHANNEL for 3 seconds to scroll through the following display modes: Local CH. 1 CH. 2 CH. 3 CH. 4 Local In the Auto Display Mode, all 4 Channel Numbers under the Right box will be displayed. In this mode, the display will scroll through data from all the valid channels, each of which will be shown for 20 seconds. FIGURE 13 In each case, batteries should be replaced. [. . . ]