User manual TRIMBLE LG2

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TRIMBLE LG2. We hope that this TRIMBLE LG2 user guide will be useful to you.


TRIMBLE LG2 : Download the complete user guide (199 Ko)

You may also download the following manuals related to this product:

   TRIMBLE LG2 (201 ko)
   TRIMBLE LG2 (202 ko)
   TRIMBLE LG2 (200 ko)
   TRIMBLE LG2 (200 ko)
   TRIMBLE LG2 (201 ko)
   TRIMBLE LG2 (199 ko)

Manual abstract: user guide TRIMBLE LG2

Detailed instructions for use are in the User's Guide.

[. . . ] Precise angles of 90°, 67. 5°, 45°, and 22. 5° are easily established with the LG2's built-in protractor. Before using the laser, be sure to read this operator's manual carefully. Included in it is information about setting up, using, and maintaining the laser. A CAUTION indicates a hazard or unsafe practice that could result in minor injury or property damage. [. . . ] Wearing them longer than necessary can affect your eyes' sensitivity to seeing color. Checking Calibration Before each use, be sure to check the laser for signs of damage. If the laser has been dropped or subjected to other rough treatment, it should be checked for accuracy. Refer to the sketch for the location of the laser at each step and for the location of the marks made at each step. All marks can be made on the floor by following the beam to the floor. Place the laser so that the laser beams intersect over point A with one of the beams pointing toward the far end of the room. Mark a point (B) on the floor at about the center of the room, on the laser line. Note: To ensure accuracy, the distances from B to A, to C, and to D should be equal. Place the laser so that the laser beams intersect over point B, making sure that one of the beams is on point C. Turn the laser 90° so that the intersecting laser beams are over point B, making sure that one beam is over point D and the other is pointing in the direction of point A. Measure the difference between points A and E and compare with the following: 90° angle is in calibration if the distance between A and E is: 10 m (30 ft) <3 mm (<1/8 inch) If the difference is more than shown in the chart, contact your local authorized service center for exchange or replacement. C Room length or distance between A and C Existing Reference or Chalk Line 22. 5° Steps 6 & 7 B D A 90° Intersection Steps 3, 4, & 5 0° B 22. 5° 67. 5° 45° 90° E A Steps 1 & 2 ­9­ ­ 10 ­ ­ 11 ­ ­ 12 ­ Specifications Accuracy Working Range* Laser Class Laser Type Battery Type Battery Life Operating Temperature Range Size (L x W x H) 6 mm @ 15 m (1/4 in. @ 50 ft) 15 m nominal, up to 30 m (50 ft nominal, up to 100 ft) 2 635 nm 2 C-cell alkaline 30 hours (alkaline) 0° to 45° C (32° to 113° F) Maintenance and Care You will get years of service from your laser by following the maintenance and care recommendations in this manual. However well the product is designed, mishaps do occur and the most common problems associated with these are covered in the following areas. Any damage to the laser caused by improper maintenance and care voids the warranty. Handling Precautions When transferring the laser from one location or job site to another, be sure to carry it in its protective carrying case. System Cleaning For maximum performance and accuracy always keep the lenses clean. Use only a good quality glass cleaner on a soft cloth to clean the exterior of the laser, its lenses, and the laser glasses. CAUTION: A dry cloth or abrasive organic cleaner could scratch or damage these surfaces. Storage When you're not using the laser, store it in its protective case. CAUTION: The batteries should be removed when storing the laser more than 30 days. Battery Disposal Some states and local areas have regulations regarding the disposal of batteries. Laser Safety This laser uses a Class 2 laser, which complies with the requirements based on the IEC825-1/EN60825 standards (Class 2 based on 21CFR 1041). [. . . ] Any evidence of negligent, abnormal use, accident, or any attempt to repair equipment by other than factory-authorized personnel Trimble certified or recommended parts, automatically voids the warranty. Special precautions have been taken to ensure the calibration of the laser; however, calibration is not covered by this warranty. The foregoing states the entire liability of Trimble regarding the purchase and use of its equipment. Trimble will not be held responsible for any consequential loss or damage of any kind. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TRIMBLE LG2




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TRIMBLE LG2 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.