User manual TP-LINK TD-8840B

[. . . ] TD-8840 User Guide ADSL2+ Modem Router Rev: 2. 0. 1 1910010192 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. http://www. tp-link. com is a registered trademark of TP-LINK TECHNOLOGIES CO. , LTD. Other brands and product names are trademarks or I FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] Obtain default gateway automatically: This radio button is checked by default. It's recommended that you keep the default settings to allow the Router to obtain the default gateway automatically. Use the following default gateway: Check this radio button then you can enter the IP address and the WAN interface for the default gateway. Obtain DNS server addresses automatically: This radio button is checked by default. It's recommended that you keep the default settings to allow the Router to obtain the default DNS server addresses automatically. Use the following DNS server addresses: Check this radio button then you can enter the primary DNS server and secondary DNS server. DHCP can be enabled for PVC in MER mode as WAN interface if "Obtain an IP address automatically" is chosen. Configuring them with static values will disable the automatic assignment from DHCP or other WAN connection. If you configure static default gateway over this PVC in MER mode, you must enter the IP address of the remote gateway in the "Use IP address". 28 TD-8840 ADSL2+ Modem Router User Guide Click Next button in Figure 4-12, and then you will see the Figure 4-13. Check or uncheck the Enable WAN Service box according to your needs. Figure 4-13 Click the Next button to enter the next step as shown in Figure 4-14. Click Save to complete the configuration. Figure 4-14 IP over ATM (IPoA) If you select the protocol of IP over ATM (IPoA), you will see the Figure 4-15. Enter the parameters provided by your ISP. 29 TD-8840 ADSL2+ Modem Router User Guide Figure 4-15 WAN IP Address: Enter the IP Address provided by your ISP. Use the following default gateway: Check this radio button then you can choose Use IP Address or Use WAN Interface. Use the following DNS server addresses: Check this radio button then you can enter the primary DNS server and secondary DNS server. Configuring them with static values will disable the automatic assignment from other WAN connection. Click Next in Figure 4-15, and then you will see the Figure 4-16. 30 TD-8840 ADSL2+ Modem Router User Guide Figure 4-16 Check or uncheck the Enable WAN Service box according to your needs. Click the Next button to enter the next step as shown in Figure 4-17, and click Save to complete the configuration. Figure 4-17 Bridging If you select the Bridging protocol, you will see the Figure 4-18. Click Save to complete the configuration. 31 TD-8840 ADSL2+ Modem Router User Guide Figure 4-18 Figure 4-19 Note: After completing any setup, the new setup must be saved and the Router must be restarted for the configuration to go into effect. Please click the Save/Reboot button to restart as shown in Figure 4-20. 32 TD-8840 ADSL2+ Modem Router User Guide Figure 4-20 Note: All of the above setup is under windows XP OS. 4. 3. 2 LAN Choose "Advanced SetupLAN" menu, and you can see and configure the Local Area Network (LAN) parameters in the screen as shown in Figure 4-21. Figure 4-21 IP Address - Enter an IP address for the Router. Subnet Mask - An address code that determines the size of the network. Normally use 255. 255. 255. 0 as the subnet mask. 33 TD-8840 Note: a. ADSL2+ Modem Router User Guide If you change the IP Address of LAN, you must use the new IP Address to log in the Router. b. If the new LAN IP Address you set is not in the same subnet, the IP Address pool of the DHCP server will change accordingly at the same time while the Virtual Server and DMZ Host will not take effect until they are re-configured. Disable/Enable DHCP Server - Disable or Enable the DHCP server. [. . . ] Select the "connect using a broadband connection that requires user name and password". Click Next to type the name of your ISP in the current page, and then click Next. If you have forgotten an existing account name or password, please connect with your ISP. To create the connection and close this wizard, click Finish to add a shortcut to this connection to your desktop. [. . . ]