User manual SYMPHONIC LCD-B20A6

[. . . ] 2) Slots and openings in the cabinet and the sides or bottom are provided for ventilation. To ensure reliable operation and to protect the unit from overheating, these openings must not be blocked or covered. Avoid installation in enclosed spaces such as bookcases unless proper ventilation is provided. 4) Do not push objects of any kind into the unit through the cabinet slots or openings as they could touch electrically live parts or short circuit parts resulting in a fire or electric shock. [. . . ] Aerial input jack Connect to an antenna, cable system or satellite system. RGB scart jack AV-IN1: Connect to the scart jack of a DVD player or set top box. Headphone jack 25 26 27 28 29 30 Connect headphone (not supplied) for personal listening. (To select channel 24, press "0" button first and then press "2" and "4". ) · If this is the channel you want, press ENTER. Channel Plan CH Indication 01­10 02­12 13­20 21­69 74­78 80­99, 100 71­86 90­106 121­141 142­153 TV Channel PAL I IRA­IRJ, GAP ­ ­ E21­E69 X, Y, Z, Z+1, Z+2 S1­S20, GAP ­ ­ S21­S41 ­ Language Selection If you want to change the language of the on-screen menu, follow the procedure below. Note: If some digits appear in the corner of the screen, press STANDBY-ON without unplugging the power cord. 4) Press Cursor K / L to point to "INITIAL", then press ENTER. ENTER. 5) Press Cursor K / L to point to "LANGUAGE", then press 6) Press Cursor K / L repeatedly to select your desired language, then press ENTER . 7) Press SETUP to exit. SETUP PICTURE BACK LIGHT [BRIGHT] INITIAL INITIAL CH TUNING LANGUAGE LANGUAGE DEUTSCH ENGLISH ESPAÑOL FRANÇAIS ITALIANO NEDERLANDS SVENSKA POLSKI Automatic Channel Presetting You can programme the tuner to scan only the channels that you can receive in your area. 1) Press STANDBY-ON to turn on the TV. 3) Press Cursor K / L to point to "INITIAL", then press ENTER . ENTER . 4) Press Cursor K / L to point to "CH TUNING", then press 5) Press Cursor K / L to point to "AUTO", then ENTER. · The tuner scans and memorises all the active channels in your area. When AUTO is completed, the lowest memorised channel reappears on the screen, and you can use PROG. +/- on the front / (prog. ) on the remote control for the memorised panel or channels. · If you press SETUP during the scanning, this operation will stop and the lowest memorised channel will appear on the TV screen. Sorting of TV channels from P01 to P06 will be performed automatically as follows. This unit can receive Hyper and Oscar frequency bands. 7) Press SETUP to exit. Note: · To confirm that a channel has been added, press / (prog. ). · If you insert the RF cable plug into the Aerial input jack P01 : BBC1 P02 : BBC2 P03 : ITV P04 : CH4 P05 : CH5 P06 : SKY NEWS after manual channel presetting, a picture will be distorted. / (prog. ) to select the same channel In this case, press again. SETUP PICTURE BACK LIGHT [BRIGHT] INITIAL INITIAL CH TUNING LANGUAGE SETUP PICTURE BACK LIGHT [BRIGHT] INITIAL INITIAL CH TUNING LANGUAGE MANUAL POSITION CHANNEL DECODER SKIP P55 055 [OFF] [OFF] CH TUNING AUTO MANUAL MOVE AUTO CH TUNING AUTO MANUAL MOVE START FINISH 5 EN L4630BA(EN). fm Page 6 Thursday, June 15, 2006 3:42 PM Decoder Allocation Some TV channels transmit encoded TV signals which can only be viewed with a purchased or hired decoder. The following function will automatically activate the connected decoder for the desired TV channel. Channel Reprogramming You can move a channel allocated to a position to another while keeping the total number of the positions the same. When you move a channel, all the other channels in the positions will be affected. 1) Press STANDBY-ON to turn on the TV. 2) Press / (prog. ) or the Number buttons to select the TV 3) 4) 5) 6) channel which you would like to allocate the decoder to. Press Cursor K / L to point to "INITIAL", then press ENTER . Press Cursor K / L to point to "CH TUNING", then press ENTER . Press Cursor K / L to point to "MANUAL", then press ENTER. 1) Follow the steps 1) to 4) in the "Automatic Channel Presetting". 2) Press Cursor K / L repeatedly to point to "MOVE", then press 3) Press Cursor K / L repeatedly to select the position number you want to change the channel, then press ENTER . · You cannot select a position number where "- - -" appears next to the number. [. . . ] When done, press SETUP to exit. SETUP PICTURE BACK LIGHT [BRIGHT] INITIAL SETUP PICTURE BACK LIGHT [NORMAL] INITIAL SETUP PICTURE BACK LIGHT [DARK] INITIAL Status Display To check the Channel number & Audio mode, press DISPLAY. Each time you press DISPLAY, TV screen will change as illustrated: When you select the channel using the Number buttons, select the desired channel (position number). <OFF> <CHANNEL NUMBER and AUDIO MODE> P08 STEREO Press once 7 EN L4630BA(EN). fm Page 8 Thursday, June 15, 2006 3:42 PM MAINTENANCE Picture Screen Cleaning · If the LCD panel should require cleaning, wipe it with a cotton or soft cloth. Before cleaning the picture screen, disconnect the power cord. Cabinet Cleaning · Wipe the front panel and other exterior surfaces of the TV with a soft cloth immersed in lukewarm water and wrung dry. Such chemicals may cause damage and discoloration to the exposed surfaces. Service · Should your LCD colour TV become inoperative, do not try to correct the problem by yourself. [. . . ]