User manual SPA-QUIP SP1200

[. . . ] Spa Water Treatment Recommended Chemical Values Chlorine. . . . . . . . . . . . . . . . . . . . . . . . . 1. 5 - 3. 0 PPM ( Parts Per Million ) pH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 - 120 PPM It is important to maintain your spa water chemistry to the above values to ensure a healthy experience both for you as bathers and for your spa pool equipment. PH This is a measure of how acid or alkaline the spa water is (below 7. 0 is acid, above 7. 0 is alkaline). [. . . ] Note that high heat may not always be available due to possible load shedding when accessories are turned on (depends on installer configuration). Range of adjustment is 0. 00 (default, off) to 5. 00 in steps of 0. 25 degrees Celsius. At the maximum setting of 5. 00, the pool water must be five or more degrees below the set temperature before the high setting will be used. Page 6 Page 27 7. 8. 7 Panel And Pool Light Synchronisation (on/off) The SP1200 touch pad backlight has the ability to mirror the colour and intensity of the in-pool Spa Power Variable Colour Light (SPVCL). This feature is most noticeable when a light effect mode is being used and the light colour is changing rapidly. When the pool light is turned off the touch pad backlight will remain one user selectable fixed colour. If desired the synchronising/mirroring feature can be disabled and the touch pad backlight will remain on the fixed colour even when the pool light is turned on. 3. 3 Pump 1 (Two speed, 24HR circulation pump fitted) This pump is controlled via two touch pad buttons - one to turn the pump on/off and another to change its speed. The mode and pump speed selected by these buttons are shown for a few seconds on the LCD display as well as being indicated by the pump button LEDs. The two pump button LEDs are green, red or off when the pump is onlow, on-high or off. Pump 1 Two pushes of the on/off button cycles the pump as follows: 7. 8. 8 Enabling/Disabling Light Synchronisation 1) 2) 3) 4) 5) Select the MISC OPTIONS submenu from the main menu. SYNC menu item Press the SCROLL button modify light synchronisation setting Use the UP and DOWN buttons to toggle between on and off Press the SCROLL button to set. Push 1 (Pump On) Push 1 (Pump Hi) The Hi/Low speed button can be used to change the pump speed: Note: This option is only available if a SPVCL (Spa Power Variable Colour Light) is in the pool. Push 2 (Pump Low) Push 2 (Pump Off) LCD displays "PUMP OFF", button LEDs off. The Hi/Low speed button has no effect in this mode. 7. 9 Advanced Options Submenu The advanced options menu contains settings that should only be modified after you are familiar with the basic operation of the spa. The defaults will generally be satisfactory and will probably not need to be changed. 9. SET TEMP USER TIMER CLOCK USER ALARM SLEEP TIMES MAINT TIMERS MISC OPTIONS ADV. DEFAULTS Pump 2 Two pushes of the on/off button cycles the pump as follows: Push 1 (Pump On) Push 1 (Pump Hi) The Hi/Low speed button can be used to change the pump speed: ADV OPTIONS () (ESC) Push 2 (Pump Low) Push 2 (Pump Off) 1. HEAT CONTROL () (SET) ( ) LCD displays "PUMP OFF", button LEDs off. The Hi/Low speed button has no effect in this mode. Scroll to SET Notes: 1) If left on, these pumps will automatically switch off after 25 minutes. 2) If the heater element is on, running either pump in high speed mode may cause the heater to load shed and switch off. If this occurs the heater will come back on approximately 5 seconds after high speed is deselected (pump running in low speed or pump off). Page 26 Page 7 3. 4 Pump 1A & 1B (Single speed pumps, no 24hr circulation pump fitted) Three pushes of the Pump 1A button cycles the pump as follows: 7. 8. 2 Main Display The SP1200 touch pad LCD consists of two lines of text and four numerical digits. The display typically shows three quantities - pool temperature, set temperature and the clock (weekday and time). By default the pool temperature is displayed on the numerical digits leaving the clock and set temperature on the two lines of text. If preferred, the user may change the layout so either the set temperature or clock are shown on the main display (four numerical digits) rather than on the smaller text lines. In addition a cycling mode can be selected whereby each of the three possible views is presented for 10 seconds each. Available options: Push 1 (Pump On) Push 2 (Pump Off) Push 3 (Pump Auto) LCD displays "PUMP ON", button LEDs green. [. . . ] This will set the timer running and the message "TIMER STARTED (STOP)" will be displayed. While this message is being displayed you may immediately stop the timer by pressing SCROLL again. Otherwise wait approximately five seconds for the message to disappear and you will be returned back to the default view with the timer running in the background. SET TEMP USER TIMER CLOCK USER ALARM SLEEP TIMES MAINT TIMERS MISC OPTIONS ADV. [. . . ]