User manual SONY RM-V202

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. 2 Features The RM-VL700 Remote Commander provides centralized control of all your AV components from a single remote commander and saves the trouble of operating different AV components with different remote control devices. [. . . ] (It is possible to make a note on the back of the supplied "Component Code Numbers. ") Notes · Some specific remote control signals may not be "learned. " · You can also use a display monitor for computer display (including a built-in tuner type), if the Commander is "learned. " Example: To program the N (Play) signal of your video cassette recorder to the VCR N (Play) button of the Commander 1 Place the RM-VL700 head to head with your component's remote control. Remote control for your component about 2 ­ 4 inches (5 ­ 10 cm) away RM-VL700 2 Press and hold SET for over 3 seconds. The SET indicator lights up, and all Component Select buttons flash. Continued 15 Programming signals of another remote control -- Learning Function (continued) 4 Press the button on the Commander you want to "teach. " 3 Press the Component Select button for the component whose signals are to be "learned. " Both the SET indicator and the selected Component Select button flash (Learning function standby). Both the SET indicator and the selected Component Select button light up, and all other buttons turn off. If another signal has already been "learned" by that button The SET indicator flashes twice, and the Commander takes no action returning to its state after the Component Select button was pressed in Step 3. Either "teach" to another free button, or clear the already "learned" function (page 21) and start over from the beginning. 16 5 Press and hold the button on the other remote control, until both the SET indicator and the Component Select button lights up again. During data transfer, only the SET indicator stays lit, and the Component Select button turns off. After data transfer is complete, the Commander returns to its state in Step 3. Notes · If you do not perform Learning steps within 20 seconds at any point during the process, Learning mode ends. · If you do not perform Step 5 within 10 seconds after Step 4, the learning procedure returns to Step 3. Repeat Step 4. To cancel setup, press SET. If the Commander does not seem to be working If the "learned" button does not operate properly, "teach" once again. (For example, if the volume becomes very loud after pressing VOL+ only once, noise may have interfered during the Learning procedure. ) remote control of component If you set a component code after "learning" a signal If you have programmed any signal on a button by the Learning function, that signal will work even after you set a component code. Note on the REC zsignal You can only "teach" to one button at a time. Therefore you cannot teach a sequential button operation (for example REC z + B) to a single button on the Commander. In this case, "teach" the functions of each button on your component to the Commander. during data transfer data transfer complete If the SET indicator flashes five times It means that "learning" is incomplete. Repeat steps 4 and 5. 6 Repeat Steps 4 and 5 to "teach" functions to other buttons. To "teach" another component's remote control signal After positioning the two remote commanders as in Step 1 on page 15, press the corresponding Component Select button, and then follow Steps 4 and 5 to perform Learning. 7 Press SET to finish setting. Continued 17 Programming signals of another remote control -- Learning Function (continued) For accurate Learning ·Do not move the remote units during the Learning procedure. ·Be sure to keep holding down the "learning" button until your Commander reacts as described. ·Avoid Learning in places subject to direct sunlight or a strong fluorescent light. The following table shows the factory setting of which volume would be controlled for each component. Component Select button TV VCR CBL/SAT DVD AMP Controls the volume of TV TV TV TV amplifier However, if your visual components are connected to an audio system, you may want to hear TV or VCR sound from the loudspeakers via your amplifier, not from your TV speakers. In this case, you need to change the factory preset so that you can control the volume of your visual components without first having to switch to the amplifier. To change the Factory Preset of the Volume Control 24 1 Press SET. All Component Select buttons flash. To set only the audio components' volume controls to AMP Press VOL­ while holding MUTING pressed. Only AMP lights up when you press these buttons, and then turns off when you release them. When you press VOL-holding MUTING pressed. 2 While holding MUTING pressed, press VOL + or VOL ­. To set all volume controls to AMP Press VOL+ while holding MUTING pressed. All Component Select buttons light up when you press these buttons, and then turn off when you release them. When you press VOL+ holding MUTING pressed. The buttons turn off when you release them. Visual components are: TV, video cassette recorder, analog cable box, digital cable box, digital satellite, DVD player Audio components are: CD player, MD player, cassette deck, amplifier To cancel setting, press SET. Note If you used the Learning function to program the VOL +/­ or MUTING buttons to send a signal to a component, the procedure above will not change the function of the VOL +/­ and MUTING buttons. The buttons turn off when you release them. Volume control setting complete. 25 Adding an Extra Function to the Component Select Buttons Programming the Power-On Command of the Selected Component just by pressing that Component Select button (for Sony Components only) When using Sony components, you can program the Power-On signal for each component on a Component Select button. You can select the desired component and power it on by just pressing that Component Select button. 2 While holding POWER pressed, press the desired Component Select button. When you first press POWER, only the Component Select buttons that have already been set with the Power-On command light up. Example: If the Power-On command has been programmed on the VCR and DVD buttons, these buttons light up when you first press POWER. To cancel setting, press SET. To clear the Power-On command Repeat the same procedure, pressing the desired Component Select button that lights up when you press POWER. Notes · If the component code of a non-Sony brand has been set on a Component Select button, you cannot program the Power-On function on it. If you change the component code (page 8) after setting the Power-On function, the Power-On function is cleared. [. . . ] 8VOL +/­ Volume up: + Volume down: ­ 9MUTING To mute the volume on the TV. Press again to turn muting off. KEY DISPLAY 6f TV KEY DISPLAY 0POWER 3qd 1 ­ 9, 0, ENT FUNCTION To turn on and off. For example, to change to channel 5, press 0 and 5 (or, press 5 and ENT). To operate SLEEP function on the TV (works only for a TV with SLEEP function). [. . . ]