User manual SONY FST-ZUX9

[. . . ] 3-100-770-12(1) Mini Hi-Fi Component System Operating Instructions FST-ZUX9 ©2007 Sony Corporation WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To prevent fire, do not cover the ventilation of the apparatus with newspapers, tablecloths, curtains, etc. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. Batteries or batteries installed apparatus shall not be exposed to excessive heat such as sunshine, fire or the like. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. [. . . ] Therefore, when a USB device is connected, it cannot be recognized. 1 Press TUNER/BAND repeatedly until "FM" or "AM" lights up in the display. To change the AM tuning interval The factory setting for AM tuning interval is 9 kHz (or 10 kHz for some areas). Use the buttons on the unit for the operation. 2 Press TUNING MODE repeatedly until "MANUAL" lights up in the display. 3 Press +/­ repeatedly to tune in the station you want. You can also use TUNING +/­ on the unit. 1 Press TUNER/BAND repeatedly until "AM" lights up in the display. 2 Press "/1 to turn off the system. "AM 9K STEP" or "AM 10K STEP" appears in the display. When you change the interval, all the AM preset stations are erased. Tips · To improve broadcast reception, adjust the supplied antennas, or connect an external antenna. · When an FM stereo program has static noise, press FM MODE on the remote repeatedly until "MONO" lights up in the display. There will be no stereo effect, but the reception will improve. To improve tuner reception When tuner reception is poor, set the CD/ USB power manage function to "CD/USB POWER OFF". 3 Press "/1 while holding down x. The system turns on automatically. "CD/USB POWER OFF" appears in the display. 30GB Other operations Tape To Do this Stop playback Pause playback Press x. Push A Z PUSH OPEN/ CLOSE or B PUSH Z OPEN/CLOSE on the unit when playback is stopped. Playing a tape You can use TYPE I (normal) tape. 1 Select a tape deck. Press TAPE A/B (or FUNCTION on the remote) repeatedly to select "TAPE A" or "TAPE B". Fast forward or rewind Remove a tape 2 Load a tape. Press A Z PUSH OPEN/CLOSE or B PUSH Z OPEN/CLOSE on the unit to open Deck A or Deck B. Load a tape into the deck with the side you want to play back or record facing upward. Note Tape During playback, rewind or fast forward operation, you cannot open the tape deck. Tip If you press NX (or N on the remote) when the TAPE A function is selected and there is no tape in Deck A, the system automatically switches to the TAPE B function when there is a tape in Deck B and vice versa. Then, playback will start. Push A Z PUSH OPEN/CLOSE or B PUSH Z OPEN/CLOSE again to close the selected deck. 3 Press NX (or N on the remote). The tape starts playing. 4 Turn MASTER VOLUME (or press VOLUME +/­ on the remote) to adjust the volume. 31GB Recording onto a tape There are three ways to record on a TYPE I (normal) tape. CD-TAPE Synchro Recording: For Manual Recording and Sound Mixing: You can record tracks from AUDIO CDs and MP3 discs onto a tape. The recording level is adjusted automatically. Manual Recording: You can record just the portion you want from an audio source, including connected audio components. Sound Mixing: Press the function button to select the source you want to record. For Sound Mixing, if you want to record your voice through the microphone only, you can do so by selecting the TAPE A function and not playing any tape. · To record a folder of MP3 audio tracks, press PLAY MODE on the remote repeatedly until " " lights up in the display. Then, press +/­ repeatedly to select the folder you want. You can "mix" sound from any one of the audio sources and singing or speaking into a microphone (not supplied). The mixed sound can be recorded onto a tape. 3 Set Deck B to stand by for recording. For CD-TAPE Synchro Recording: 1 Load a recordable tape into Deck B. Be sure to load the tape with the side you want to record facing upward. Press CD-TAPE SYNC. "SYNC" and "TAPE" lights up in the display and "REC" flashes in the display. For Manual Recording and Sound Mixing: 2 Prepare the recording source. For CD-TAPE Synchro Recording: Press CD and load the disc you want to record. To record the Press PLAY MODE track from on the remote repeatedly to select Press TAPE REC PAUSE/START. "REC" flashes in the display and "TAPE" lights up in the display. 4 Press TAPE REC PAUSE/ START. You cannot listen to other sources while recording. the selected disc 1 DISC. Then, press +/­ repeatedly to select the folder you want. Note You can record tracks on all the discs in the order you want using Program Play. [. . . ] Push STOP! The USB device was removed during recording or erasing operation, and may have been damaged. NO STEP All of the programmed tracks have been erased. Not Supported You have pressed PLAY MODE on the remote during playback. Reading An unsupported USB device is connected or the USB device is connected through an USB hub. No Track The system is reading information of the disc. Some buttons are not available. NO STEP No playable MP3 audio track is loaded in the system. Not in Use You have cleared all the steps you programmed. OVER You have reached the end of the disc while pressing M during playback or pause. Step Full! You tried to perform a specific operation under conditions where that operation is prohibited. Over Current An over current was detected. You tried to program more than 25 steps. SET CLOCK! You pressed CLOCK/TIMER SELECT on the remote before the clock is set. 54GB Protected! The USB device is write-protected. Push STOP! Precautions Discs that this system CANNOT play back · Discs of non-standard shape (for example, heart, square, star). · Discs that have adhesive tape, paper, or sticker attached to them. · Rental or used discs with attached seals where the glue extends beyond the seal. [. . . ]