User manual SMC SMC7004WFW

[. . . ] BarricadeTM Plus Wireless Cable/DSL Broadband Router with VPN Wireless Cable/DSL Broadband Router with VPN N N N N N N N N N EZ 3-Click Installation Wizard IEEE 802. 11b Compliant Wireless Operation at 11, 5. 5, 2, or 1 Mbps Internet Access via ­ · 10/100 Mbps WAN port connection to xDSL/Cable modem Home Networking via ­ · Three 10/100 Mbps Ethernet switch ports with MDI/MDI-X auto-negotiation Configuarable Parental Control by limiting access to web sites with URL and keyword blocking Stateful Packet Inspection (SPI) Advanced Firewall Protection Client Privileges, Intrusion Detection, NAT Built-in VPN Tunneling Capability User Guide SMC7004WFW BarricadeTM Plus Wireless Cable/DSL Broadband Router User Guide From SMC's Barricade line of Broadband Routers Sept 2002 Revision Number: R01 COMPLIANCES FCC - Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. [. . . ] To communicate with the Wireless Barricade Plus, the NMS must first submit a valid community string for authentication. The options for configuring community strings and related trap functions are described in the following sections. 4-43 NETWORKING AND CLIENT SERVICES Community Community: Access: Valid: A community name authorized for management access. Sets administrative status of entry to enabled or disabled. Note: Up to 5 community names may be entered. 4-44 CONFIGURING THE WIRELESS BARRICADE PLUS Trap IP Address: Community: Version: IP address of the trap manager. Sets trap status of entry to disabled, or enabled with V1 or V2c. 4-45 NETWORKING AND CLIENT SERVICES Tools You can use the "Tools" menu to restore factory settings, update firmware, or reboot the Wireless Barricade Plus. 4-46 CONFIGURING THE WIRELESS BARRICADE PLUS Configuration Tools The "Backup" option allows you to save your Wireless Barricade Plus' configuration to a file named config. bin on your PC. You can then click on the "Restore" radio button to restore the saved backup configuration file. Selecting the "Restore to Factory Defaults" can restore the factory settings. 4-47 NETWORKING AND CLIENT SERVICES Firmware Upgrade Use this screen to update the latest firmware using a file provided by SMC. Note: For latest firmware version information, visit SMC's Web site at http://www. smc-europe. com. 4-48 CONFIGURING THE WIRELESS BARRICADE PLUS Reset If the Wireless Barricade Plus stops responding, you can click on the "Apply" button to refresh the gateway. The saved configurations of the Wireless Barricade Plus will not be changed back to factory default settings after resetting the gateway. Note: If you use the reset button on the rear panel, the Wireless Barricade Plus performs a power reset and restores the factory settings. 4-49 NETWORKING AND CLIENT SERVICES Status You can use the following screen to display WAN/LAN connection status, firmware and hardware version numbers, as well as information on all DHCP clients connected to your network. 4-50 CONFIGURING THE WIRELESS BARRICADE PLUS The following items are included in this screen: Field INTERNET GATEWAY INFORMATION Description Displays WAN connection type and status. Displays system IP settings, as well as DHCP, NAT, PPTP Client and PPTP Server Firewall. Displays the number of attached clients, the firmware versions, the physical MAC address for each media interface, as well as the hardware version and serial number. Click on this button to reconnect to the Internet via cable/DSL modem. Displays information on all DHCP clients on your network. Release Renew Security Log DHCP Client Log 4-51 NETWORKING AND CLIENT SERVICES 4-52 CHAPTER 5 CONFIGURING CLIENT TCP/IP If you have not previously installed the TCP/IP protocol on your client PCs, refer to the following section. If you need information on how to configure a TCP/IP address on a PC, refer to "Setting TCP/IP to Work with the Wireless Barricade Plus" on page 5-5. Installing TCP/IP Protocol in Your PC Windows 95/98/ME 1. Click the "Start" button and choose "Settings, " then click "Control Panel. " 2. Double click the "Network" icon and select the "Configuration" tab in the Network window. Click the "Add" button to add the network component to your PC. Double click "Protocol" to add the TCP/IP protocol. 5-1 INSTALLING TCP/IP PROTOCOL IN YOUR PC 5. Click the "OK" button to return to the Network window. 6. Click "OK" to complete the install procedure and restart your PC to enable the TCP/IP protocol. 5-2 CONFIGURING CLIENT TCP/IP Windows 2000 1. Click the "Start" button and choose "Settings, " then click "Control Panel. " 2. Double click the "Network and Dial-up Connections" icon, then "Local Area Connection" icon, and press the "Properties" button in the "General" tab. [. . . ] Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC. Any product returned to SMC without a valid Return Material Authorization (RMA) number clearly marked on the outside of the package will be returned to customer at customer's expense. Customers are responsible for all shipping charges from their facility to SMC. SMC is responsible for return shipping charges from SMC to customer. i LIMITED WARRANTY WARRANTIES EXCLUSIVE: IF A SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC'S OPTION. [. . . ]