User manual SHURE MC GUIDE SUPPLEMENT

[. . . ] UHF Wireless System USER'S GUIDE SUPPLEMENT MC (774­782 MHZ) CONTENTS SPECIFICATIONS . [. . . ] (UA840) Battery Life (Typical) 12 hours (with Duracell MN1500 1. 5V AA alkaline battery) Operating Temperature Range -20° to 50° C (-4° to 122° F) NOTE: Battery characteristics may limit this range 2 Overall Dimensions U1: 92. 2 mm L x 64. 7 mm W x 24. 2 mm D (3­29/32 x 2­35/64 x 61/64 in. ) U2/58:254 mm L x 50. 8 mm Dia. (8­1/2 x 2 in. ) U4S/U4D: 44. 5 mm H x 482. 6 mm W x 295. 3 mm D (1­3/4 x 19 x 11­5/8 in. ) Net Weight U1: 175. 2 g (6. 1 oz. ) without battery U2/58, U2/BETA 58: 375. 6 g (13. 2 oz. ) without battery U2/87, U2/BETA 87: 303. 1 g (10. 7 oz) without battery U4S: 3. 30 kg (7. 27 lbs) U4D: 3. 85 kg (8. 48 lbs) Certification U1, U2: BAPT Type Approved to FTZ 17TR 2019 and BAPT 122 R1; EMC Approved to ETS 300 445. BAPT Type Approved to FTZ 17TR 2019 and BAPT 122 R1; EMC Approved to ETS 300 445. UHF Type Approved and EMC Approved systems are eligible to carry the CE marking. U1 Transmitter Input (Figure 1) Connector: Input Configuration: Actual Impedance: Maximum Input Level: 4-Pin Female miniature Connector TA4F Pin Assignments: LEMO Connector Pin Assignments: Voltage for Remote Power: 4-Pin Female Miniature Connector TA4F or LEMO connector (optional) Unbalanced, active 18 k with lavalier microphone 1 M with instrument cable 6 Vp­p (+7 dBV) for 1% THD at minimum gain setting using 1 kHz signal. Pin 1: Tied to Ground Pin 2: Tied to +5 V Pin 3: Tied to Audio Pin 4: Tied thru 20k Resistor to Ground. (On instrument adapter cable, Pin 4 floats) Pin 1: Tied to Pin 3 and 10 k to Ground Pin 2: +5V Pin 3: Tied to Pin 1 Pin 4: Tied to Shield (Ground for Positive Bias) +5 V supplied to microphone cartridge U1 Transmitter Output Connector: Actual Impedance: Nominal Output Level: Maximum Output Level: Pin Assignments: SMC 50 +10 dBm +11 dBm Shell = Ground Center = Signal 3 U2 Transmitter Input Input Configuration: Actual Impedance: Maximum Input Level: Unbalanced, active 20 k 3 Vp­p (0. 5 dBV) for 1% THD at minimum gain setting using 1 kHz signal. U1 MIC JACK BOARD 2 4 2 4 20K 3 1 3 1 500 27 pF GROUND AUDIO 500 27 pF +5 V MICROPHONE ELEMENT NOTE: LAVALIER MIC TIES PINS 3 AND 4 TOGETHER; GUITAR CABLE DOES NOT. U1L (LEMO 4 PIN) MIC JACK BOARD 499 499 27 pF 1 AUDIO 27 pF 2 10K BIAS 3 4 SHIELD FIGURE 1 U2 Transmitter Output Connector: Actual Impedance: Nominal Output Level: Maximum Output Level: Pin Assignments: SMC 50 +10 dBm +11 dBm Shell = Ground Center = Signal 4 U4S and U4D Receiver Input Connector: Connector Type: Actual Impedance: Nominal Input Level: Maximum Input Level: Pin Assignments: Voltage for Remote Power: Antenna BNC 50 ­95 to ­30 dBm +6 dBm (­20 dBm recommended) Shell = Ground Center = Signal 12 Vdc, 150 mA maximum Power Input IEC ­­ 90­230 VAC, 50/60 Hz 230 VAC, 50/60 Hz Network Interface 25­Pin D ­­ CMOS Logic ­­ IEC Standard ­­ ­­ 5V, 700 mA max. U4S and U4D Receiver Output Connector: Output Configuration: Actual Impedance: Nominal Input Level: Pin Assignments: Monitor Power Output High Z Audio Low Z Audio* Network Interface Unbalanced mono, 1/4 inch 300 ­­ Tip = Hot Ring = Hot Sleeve = Gnd Yes ­­ ­­ 90 to 230 VAC, 5A IEC Standard Unbalanced 1 k ­­ Tip = Hot Ring/ Sleeve = Gnd Yes Balanced 30 ­­ 1 = Ground 2 = Hot 3 = Hot Yes See Appendix See Appendix CMOS Logic See Appendix Voltage/ Current/ Phantom Power Protection? ­­ 5V, 700 mA resettable polyfuse *Output Level: Microphone Level = Line Level ­ 30 dB FURNISHED ACCESSORIES Microphone Stand Adapter (U2) . WA360 1. 8 Meter (6 ft) Receiver-Mixer Cable (1/4" phone to XLR) . UA870MC REPLACEMENT PARTS Hardware Kit (screwdriver, mounting feet, cable clamps) . [. . . ] Phone: 847-866­2200 Fax: 847-866-2279 In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414 In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055 Elsewhere, Phone: 847-866­2200 Fax: 847-866-2585 [. . . ]