User manual SHARP CD-MPS700W
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SHARP CD-MPS700W. We hope that this SHARP CD-MPS700W user guide will be useful to you.
Manual abstract: user guide SHARP CD-MPS700W
Detailed instructions for use are in the User's Guide.
[. . . ] Mini sistemi CD-MPS700W composto da CD-MPS700W (apparecchio principale) e CP-ES222H (sistema di diffusori). CD-MPS700W mini systeem bestaande uit CD-MPS700W (hoofdtoestel) en CPES222H (luidsprekersysteem). CD-MPS700W Mini Sistema de Componentes composto de CD-MPS700W (unidade principal) e CP-ES222H (sistema de alto-falante). CD-MPS700W Mini Component System consisting of CD-MPS700W (main unit) and CP-ES222H (speaker system).
CD-MPS700W
BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE MANEJO BRUKSANVISNING MANUALE DI ISTRUZIONI GEBRUIKSAANWIJZING MANUAL DE OPERAO OPERATION MANUAL
DEUTSCH FRANAIS ESPAOL SVENSKA ITALIANO NEDERLANDS PORTUGUS ENGLISH
Siehe Seiten i bis vi und D-1 bis D-28. [. . . ] Exposing the sensor on the unit to strong light may interfere with operation. Keep the remote control away from moisture, heat, shock, and vibrations.
CD-MPS700W
ENGLISH
3
Test of the remote control
The remote control can be used within the range shown below: Press the ON/STAND-BY button. Now, you can enjoy music.
Remote sensor
Precautions for battery use: Replace all old batteries with new ones at the same time. Remove the batteries if the unit is not to be used for long periods of time. Caution: Do not use rechargeable batteries (nickel-cadmium battery, etc. ). Installing the batteries incorrectly may cause the unit to malfunction.
0. 2 m - 6 m (8" - 20')
Preparation for Use
Check the remote control after checking all the connections (see pages 7 - 8). Point the remote control directly at the remote sensor on the unit.
8
E-6
03/10/29
CD-MPS700W(H)E. fm
TINSZA002SJZZ
CD-MPS700W
System connections
AM loop aerial FM aerial
Make sure to unplug the AC power lead before any connections.
ENGLISH
FM/AM loop aerial connection
Connect the FM/AM loop aerial to the ANTENNA socket. Position the FM aerial wire and rotate the AM loop aerial for optimum reception. Place the AM loop aerial on a shelf, or attach it to a stand or a wall. Notes: Placing the aerial on the stereo system or near the AC power lead may cause noise pickup. Installing the AM loop aerial: < Assembling >
3
Right speaker
Left speaker
Preparation for Use
< Attaching to the wall >
Wall
Screws (not supplied)
TINSZA002SJZZ
Wall socket (AC 230 V, 50 Hz) Red Black
E-7
03/10/29
CD-MPS700W(H)E. fm
TINSZA002SJZZ
CD-MPS700W
ENGLISH
Speaker connection
Connect the black wire to the minus (-) terminal, and the red wire to the plus (+) terminal. (AM 12:00 - PM 11:59) Note that this can only be set when the unit is first installed or it has been reset. [Refer to "Clearing all the memory (reset)" on page 26 for details. ]
"0:00"
Basic Operation
8
E-10
03/10/29
CD-MPS700W(H)E. fm
TINSZA002SJZZ
CD-MPS700W
Listening to a CD (CDs)
This system can also play audio CD-R and CD-RW discs, but cannot record. Some audio CD-R and CD-RW discs may not be playable due to the state of disc or the device that was used for recording.
ENGLISH
4
Place the CD(s) on the disc tray, label side up. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. Be sure to place 8 cm (3") CDs in the middle of the disc positions.
12 cm (5")
8 cm (3")
CD Playback
5
Press the OPEN/CLOSE
button to close the disc tray.
Total number of tracks on the CD whose number is flashing
Total playing time of the CD whose number is flashing
6 7 1 2 3
Press the ON/STAND-BY button to turn the power on. Press the OPEN/CLOSE button to open the disc tray.
To select the CD you want to listen to first, press one of the 1 - 3 buttons on the remote control. button to
Playback will begin from track 1 on the disc you have selected to play. After that disc finishes playing, the next disc will automatically start playback. When the last track on the third disc has finished playing, the CD player will automatically stop. When there is no CD in one of the disc 1 - 3 positions, that position will be skipped and the next CD will begin to play.
E-11
03/10/29
CD-MPS700W(H)E. fm
TINSZA002SJZZ
CD-MPS700W
ENGLISH
To interrupt playback: Press the button on the remote control. To resume playback from the same point, press the
To locate the beginning of a track
button. [. . . ] ) button.
Play the VCR, DVD, etc.
Headphones
Before plugging in or unplugging the headphones, reduce the volume. Be sure your headphones have a 3. 5 mm (1/8") diameter plug and are between 16 ohms and 50 ohms impedance. Adjust the volume using the VOLUME buttons.
Advanced Features
Play the connected equipment.
8
E-24
03/10/29
CD-MPS700W(H)E. fm
TINSZA002SJZZ
CD-MPS700W
Troubleshooting chart
Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorised SHARP dealer or service centre.
ENGLISH
Tuner
Symptom The radio makes unusual noises continuously. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SHARP CD-MPS700W
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SHARP CD-MPS700W will begin.