User manual SAMSUNG NP400B5BI

[. . . ] €¢ Smart Care Samsung’s Smart Care, an automatic error-monitoring system, detects and diagnoses problems at an early stage and provides a quick and easy solution. With the innovative Smart Remote Control technology, you can also be alerted when the problem occurs via your smart phones. €¢ Steam Cycle This cycle sprays a small amount of water into the drum of the dryer after several minutes of tumbling with heat. It reduces bad odors from clothing that are difficult to remove when washing with water, and also reduces wrinkles. [. . . ] Attach the ‘Y” connector to the brass male end of the small hose. Using the pliers, tighten the coupling with an additional twothirds turn. Attach the angled end of long hoses to the fill valve at the bottom of the dryer rear frame. Screw on the coupling by hand until it is seated on the fill valve connector. Attach the washer hose to the other side of the “Y” connector. Using pliers, tighten the coupling with an additional two thirds turn. Check for leaks around the “Y” connector, faucets and hoses. Duct Exhaust Short hose (Inlet to cold water) “Y” connector Long hose Frame (back) Water Hose 20_ Installing your dryer DV435-02836G-02_EN_20121123. Indd 20 2012-11-23 5:03:32 REPLACEMENT PARTS AND ACCESSORIES If your dryer requires replacement parts or accessories, contact the dealer where you purchased your dryer or the SAMSUNG customer care center at 1-800-SAMSUNG (726-7864). INSTALLATION For the proper installation, we recommend that you hire a qualified installer. Consider installing the dryer and washer sideby-side, to allow access to the gas, electrical, and exhaust connections. Connect the neutral wire (white or center wire) of the power cord and the appliance ground wire (green with yellow stripes) under the central screw of the terminal block. Insert the tab of the terminal block cover into your dryer’s rear panel slot. 1 2 3 4 5 6 External ground connector Green or bare copper wire of the power cord 3/4 in. 9 cm) UL-listed strain relief Center silver-colored terminal block screw Grounding wire (green/yellow) Neutral wire (white or center wire) 8. With a level, check your dryer and make the necessary adjustments to the leveling legs. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are complete. Plug in your dryer, and check its operation by using the checklist below. (GAS MODELS ONLY) The burner may not ignite initially due to air in the gas line. If the gas does not ignite within 5 minutes, turn your dryer off and wait 5 minutes. In order to confirm the gas ignition, check the exhaust for heat. Indd 23 2012-11-23 5:03:33 Installing your dryer FINAL INSTALLATION CHECKLIST • • • • • • • the dryer is plugged into an electrical outlet and is properly grounded. [. . . ] All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of this product and shall not apply to the following: damage that occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning, or other acts of nature or God; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG that damage this product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal and reinstallation; problems caused by pest infestations. This limited warranty does not cover problems resulting from incorrect electric current, voltage or supply, light bulbs, house fuses, house wiring, cost of a service call for instructions, or fixing installation errors. [. . . ]