User manual PRINCETON LCD15

[. . . ] If the product exhibits a distinct change in performance, indicating a need for service. u · - Power and extension cords Do not allow anything to rest on the power cord. If the power source is 120 V AC, use a power cord that has UL and C-UL approvals. If the power source is a 240 V AC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European country's safety regulations, such as VDE for Germany. Ensure that the total of all units plugged into the wall outlet does not exceed 10 amperes. [. . . ] Operation in a residential area may cause unacceptable interference to radio and TV reception requiring the owner or operator to take whatever steps necessary to correct the interference. 4 Product Description Congratulations on your purchasing this flat panel monitor of new generation. Your LCD monitor incorporates high quality display into a small light weighted module. You will certainly benefit from this monitor in lots of ways; to name some of them, comfort, safety, health, and environmental protection. This LCD monitor incorporates 15" color active matrix thin-filmtransistor (TFT) liquid crystal display to provide superior display performance. A maximum resolution of XGA 1024x768 is ideal for displaying complex graphics and high definition images. Other outstanding designs that enhance this LCD monitor's performance are Plug & Play compatibility, audio system and OSD (On Screen Display) controls. Package Contents Included with your LCD monitor are following items: · · · · · 15" TFT liquid crystal display monitor D-sub 15 pin signal cable AC power cable Audio cable This user's manual 5 Product Features l High contrast color TFT LCD display support resolution up to XGA 1024x768. Equipped with TCO selection. l l l l l l l Cleaning l Gently wipe the screen with a clean camel hair lens brush, or a soft, clean, lint-free cloth. Do not pour or spray any liquid directly onto the screen or case of the LCD monitor. Chemical cleaners have been reported to damage the screen or case of the LCD monitor. l l 6 Taking a Look Front View 1. Power Switch on or off. Pressing this button turns the display system power 2. Power LED This LED indicates different status when this unit operates in different modes. Menu/Select Pressing this button pops up the OSD menus on the screen, and used to select ("Up" direction) the OSD control options on the screen. Menu/Select Pressing this button pops up the OSD menus on the screen, and used to select ("Down" direction) the OSD control options on the screen. + This button is used to adjust the increasing value of the selected OSD control option. - This button is used to adjust the decreasing value of the selected OSD control option. Signal Connector signal connector. This is for connecting the power cable. Audio In This can be connected to the audio-out connector of the computer. 8 WARNING When you disconnect the cord/cables, be sure to hold the connector instead of the wire part. 1. Connect one end of the power cord to the monitor and the other end to the AC outlet. Connect one end of the signal cable to the rear side of computer and the other to the LCD monitor. Tighten by turning clockwise the two thumb screws to ensure proper grounding. Connect either end of the audio cable to the Audio In connector on the monitor and the other end to the audio-out connector of your computer (Z) 4. Pressing the power button on front panel turns the display system power on. (·) 9 Display Angle Tilting For viewing clarity, you can tilt the LCD forward (up to 5 degrees) or backward (up to 15 degrees. ) CAUTION In order to protect the LCD, be sure to hold the base when you adjust the LCD, and, do not touch the screen. Controls and Adjustment Adjusting with the OSD Control · To Display and Select the OSD Functions: Pressing , , + or - once pops up the OSD function main menu. Pressing option. or a second time to select the different OSD control 10 · To Adjust the Value of the Control Option: Pressing + / - button changes the value of the selected OSD control option. After adjusting values, the monitor will automatically save the changes. [. . . ] Turn off the power and check the monitor's power cord and signal cable for proper connection. The characters on the screen are dim. · Refer to the Controls and Adjustments section to adjust the brightness. The screen is blank. · During operation, the monitor screen may automatically turn off as a result of Power Saving feature. Refer to the Controls and Adjustments section to adjust the brightness. · The screen flashes when it's initialized. [. . . ]