User manual PIONEER XC-IS21T

[. . . ] FOLLOW INSTRUCTIONS -- All operating and use instructions should be followed. The product should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzine, insecticides or other volatile liquids since they may corrode the cabinet. ATTACHMENTS -- Do not use attachments not recommended by the product manufacturer as they may cause hazards. [. . . ] TIMER ­ Press to access the timer menu for setting the wake-up, sleep and record timers. 5 1 ¡ ­ Press to scan backwards/forwards on the CD/tape/MD currently playing. 6 ­ + (4 ¢) ­ Use to switch between menu options; adjust the sound; change the preset station number when listening to the tuner; or skip tracks on the currently playing CD/tape/MD. 4 RPT[-1] ­ Indicates the repeat mode (RPT for repeat disc; RPT-1 for repeat track). 6 Record timer ­ Lights when the record timer has been set for the tape deck, MD recorder or CD-Recorder. 7 Timer set indicator ­ Indicates that the wake-up and/or the record timer have been set. 10 ATT ­ Lights when the auxiliary input signal is being attenuated (reduced in level). 1 Top cover ­ Remove to access the antenna terminals and auxiliary inputs 2 STANDBY/ON ­ Press to switch the system on or into standby 3 VOL ­ ­ Use to reduce the volume 4 VOL + ­ Use to increase the volume 5 7 ­ Press to stop the currently playing CD 6 6 ­ Press to start CD playback, or pause a disc that's already playing (press again to restart) 7 OPEN/CLOSE ­ Press to open/close the disc compartment 8 Disc compartment ­ The disc compartment automatically opens when you move your hand near 9 Standby indicator ­ Lights when the system is in standby and lights green when the system is in timerstandby mode. 1 Power indicator ­ lights when the system is on 2 Headphone jack ­ plug in a pair of headphones for private listening (the sound from the speakers is muted when headphones are plugged in) Many of the features of this system are accessed from menus displayed in the CD tuner's fluorescent display. The advantage of this is that you can use many of the features using just four buttons: MENU to display the first menu option; 4 and ¢ to change the displayed option; and SET to select it. Different menu options appear depending on which component you're listening to; CD, radio, tape, MD, or a component connected to the auxiliary inputs (AUX IN). If there's already a disc in the player, then pressing the CD button--even when the system is in standby mode--will switch the system on and start the disc playing. Be careful not to trap your fingers in the disc compartment as it closes automatically. The automatic opening of the disc compartment works using an infrared sensor. The room is lit using fluorescent lights · the unit is on a dark-colored surface · The unit is placed adjacent to a wall or other surface On its default setting, the door open sensor may open the disc compartment even if a CD is playing. You can change this so that it will only work if the CD player is stopped, or you can switch it off altogether (see page 49). Volume is adjustable from zero (silence) to 36 (maximum volume) using the volume + and ­ buttons on the remote. You can also adjust the bass, treble, balance and subwoofer level to get the sound you want. Start a disc playing before working through the steps below so that you can hear the effect of changes as you make them. In step 3, if more than 5 seconds goes by without you pressing a button, the system goes ahead and sets the new level for you, without you having to press SET (step 4). The tuner can receive both FM and AM broadcasts, and lets you memorize your favorite stations so you don't have to manually tune in every time you want to listen. Here we run through the basic tuner controls, including switching between AM and FM, and tuning to a station. [. . . ] The door open sensor on the front of the CD tuner has three operating modes, as well as an off setting. Remember: switch between menu options using 4 and ¢; select the option by pressing SET. When the demo mode is set to on, the demo sequence starts if the unit is idle for more than 5 minutes, unless: · the function is set to AUX or TUNER · The display is showing the time or calendar Press any button to exit the demo sequence once it's started. If you would rather switch off the demo completely, here's how to do it. [. . . ]