User manual PIONEER VSX-LX52

[. . . ] Operating Instructions audio/video multi-channel receiver IMPORTANT The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_A1_En Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT: THE MOULDED PLUG This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. [. . . ] When PURE is selected, the signals are output with the same resolution as when input (At this time, video signals are only output from the same type of terminals to which they were input). · When a display is connected by HDMI, if this is set to something other than PURE and 480i/576i analog signals are input, 480p/576p signals are output from the component output terminals. b. · If the image doesn't match your monitor type, adjust the aspect ratio on the source component or on the monitor. · NORMAL setting is only displayed when 480i/p or 576i/p video signals are being input. 62 En Using other functions 08 Switching the speaker system If you selected Speaker B in Surround back speaker setting on page 85, three speaker system settings are possible using SPEAKERS. If you selected Normal, Front Bi-Amp or ZONE 2, the button will simply switch your main speaker system on or off. The options below are for the Speaker B setting only. 1 VSX-LX52 Using the MULTI-ZONE controls The following steps use the front panel controls to adjust the sub zone volume and select sources. See MULTIZONE remote controls on page 64. VSX-LX52 STANDBY/ON ENTER BAND TUNE PQLS HDMI PRESET PRESET TUNER EDIT INPUT SELECTOR ENTER SPEAKERS MULTI-ZONE CONTROL ON / OFF MASTER VOLUME PQLS HDMI PRESET PRESET TUNER EDIT VANCED RROUND STANDARD SURROUND HOME THX SPEAKERS MULTI-ZONE CONTROL ON / OFF MASTER VOLUME PHONES VIDEO CAMERA iPod iPhone MCACC SETUP MIC USB HDMI 4 VIDEO CAMERA iPod iPhone MCACC SETUP MIC USB HDMI 4 1 Press MULTI-ZONE ON/OFF on the front panel. Each press selects a MULTI-ZONE option: · Use SPEAKERS on the front panel to select a speaker system setting. As mentioned above, if you have selected Normal, the button will simply switch your main speaker system (A) on or off. Press repeatedly to choose a speaker system option: · SPA ­ Sound is output from speaker system A and the same signal is output from the pre-out terminals. · SPB ­ Sound is output from the two speakers connected to speaker system B. The same signal is output from the surround back channel pre-out terminals. · SPAB ­ Sound is output from speaker system A (up to 5 channels, depending on the source), the two speakers in speaker system B, and the subwoofer. The sound from speaker system B will be the same as the sound from speaker system A (multichannel sources will be downmixed to 2 channels). The same sound is output from the pre-out terminals (including from your subwoofer, if connected) as when selecting speaker system A (above). · ZONE 2 ON ­ Selects your primary (ZONE 2) sub zone · ZONE 2&3 ON ­ Select both sub zones · ZONE 3 ON ­ Selects your secondary (ZONE 3) sub zone · MULTI ZONE OFF ­ Switches the MULTI-ZONE feature off The MULTI-ZONE indicator lights when the MULTI-ZONE control has been switched ON. 2 Press MULTI-ZONE CONTROL on the front panel to select the sub zone(s) you want. If you selected ZONE 2&3 ON above, you can toggle between ZONE 2 and ZONE 3. · When the receiver is on, 2 make sure that any operations for the sub zone are done while ZONE and your selected sub zone(s) show in the display. If this is not showing, the front panel controls affect the main zone only. 3 Use the INPUT SELECTOR dial to select the source for the zone you have selected. For example, ZONE 2 CD-R sends the source connected to the CD-R inputs to the primary (ZONE 2) sub room. [. . . ] THX Select2 Games mode is unique as it gives you a smooth transition of audio in all points of the surround field. All other trademarks are the property of their respective owners. 103 En 12 Additional information Auto Surround, ALC and Stream Direct with different input signal formats The following charts show what you will hear with different input signal formats, depending on the Stream Direct mode (see Using Stream Direct on page 53) you have selected. Stereo (2 channel) signal formats Input signal format Surround Back speaker(s): Connected Dolby Digital Surround DTS Surround Other stereo sources Analog sources PCM sources DVD-A sources SACD sources Surround Back speaker(s): Not connected Dolby Digital Surround DTS Surround Other stereo sources Analog sources PCM sources DVD-A sources SACD sources 2 Pro Logic ll MOVIE Neo:6 CINEMA Stereo playback As above As above As above As above 2 Pro Logic ll MOVIE Neo:6 CINEMA Stereo playback ANALOG DIRECT (stereo) Stereo playback As above As above 2 Pro Logic llx MOVIE Neo:6 CINEMA Stereo playback As above As above As above As above 2 Pro Logic llx MOVIE Neo:6 CINEMA Stereo playback ANALOG DIRECT (stereo) Stereo playback As above As above Auto Surround / ALC / DIRECT PURE DIRECT Multichannel signal formats Input signal format Surround Back speaker(s): Connected Dolby Digital EX (6. 1 channel flagged) DTS-ES (6. 1 channel sources/6. 1 channel flagged) DTS sources (5. 1 channel encoding) DTS-HD sources Other 6. 1/7. 1 channel sources Other 5. 1 channel sources Surround Back speaker(s): Not connected DVD-A sources/Multi-ch PCM SACD sources (5. 1 channel encoding) Other 5. 1/6. 1/7. 1 channel sources a. Unavailable with only one surround back speaker connected. Auto Surround / ALC Dolby Digital EX 2 Pro Logic llx MOVIEa DTS-ES (Matrix/Discrete) DTS+Neo:6 Straight decoding As above Dolby Digital EX 2 Pro Logic llx MOVIEa Straight decoding As above As above PURE DIRECT / DIRECT Dolby Digital EX 2 Pro Logic llx MOVIEa DTS-ES (Matrix/Discrete) Straight decoding As above As above As above Straight decoding As above As above 104 En Additional information 12 Preset code list You should have no problem controlling a component if you find the manufacturer in this list, but please note that there are cases where codes for the manufacturer in the list will not work for the model that you are using. There are also cases where only certain functions may be controllable after assigning the proper preset code. example: TV General Pioneer 10037 Category Preset code Manufacturer TV General Pioneer 10037, 10166, 10679, 11247, 11260, 11398 A. R. [. . . ]