User manual PIONEER VSX-D912K
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PIONEER VSX-D912K. We hope that this PIONEER VSX-D912K user guide will be useful to you.
Manual abstract: user guide PIONEER VSX-D912K
Detailed instructions for use are in the User's Guide.
[. . . ] AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-D912
Operating Instructions
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
IMPORTANT NOTICE
H006AEn
The serial number for this equipment is located in the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. [. . . ] when the headphones are connected, the PHONES SURROUND mode will automatically be selected. · You can't use the Advanced Surround listening modes with 96kHz PCM or DTS 96kHz/24 bit sources.
38
En
Playing sources
06
· The Advanced Surround effects can be adjusted in the range of 10 to 90 by pressing RCV then pressing EFFECT +/ . The Standard mode cannot be changed.
39
En
06
Playing sources
Using the Surround Back Channel (SB CH)
· Default setting: SB ON You can have the receiver automatically switch to Dolby Digital EX or DTS-ES decoding for 6. 1 encoded sources (SB AUTO), or you can choose to listen to other kinds of sources (for example, 5. 1 encoded material) with 6. 1 encoding (SB ON). With 5. 1 encoded sources, a surround back channel will be generated, but the material may sound better in the 5. 1 format for which it was originally encoded, in which case you can simply switch the surround back channel off (SB OFF). The table indicates when you will hear the surround back channel.
· Press SB CH MODE (front panel) repeatedly to cycle the surround back channel options. Each press cycles through the options as follows:
SB ON SB OFF SB AUTO
· You can't use the surround back channel if the Surround back speaker setting on page 46 is set to SB SW or SB . · You can't hear the surround back channel with DTS 96kHz/24 bit sources.
STANDARD Type of source SB CH MODE ON AUTO ON AUTO STANDARD decoding MOVIE/MUSIC/ PROLOGIC NEO:6 CINEMA/ NEO:6 MUSIC
ADVANCED SURROUND All modes
DTS-ES/Dolby Digital Matrix encoded multi-channel sources with 6. 1 surround Dolby Digital/DTS encoded multi-channel sources Dolby Digital/DTS encoded stereo sources, Stereo sources Analog 2-channel (stereo) source
ON AUTO ON AUTO
40
En
Playing sources
06
Using the Virtual Surround Back mode (VSB)
Selecting this mode allows you to hear a virtual back channel through your surround speakers. For example, you can choose to listen to sources with no surround back channel information (for example, 5. 1 encoded material) with emulated 6. 1 encoding (VSB ON). Sometimes the material may sound better in the 5. 1 format for which it was originally encoded. In this case you can have the receiver only apply this effect to 6. 1 encoded sources like Dolby Digital EX or DTSES (VSB AUTO), or you can simply switch it off (VSB OFF). The table indicates when you will hear the virtual surround back channel. · Press SB CH MODE (front panel) repeatedly to cycle the virtual surround back channel options.
Virtual Surround Back mode ON AUTO ON AUTO
Each press cycles through the options as follows:
VSB ON VSB OFF VSB AUTO
· You can't use the Virtual Surround Back mode if the Speaker setting on page 45 is set to S . · You can only use the Virtual Surround Back mode if the surround speakers are on and the Surround back speaker setting on page 46 is set to SB or SB SW. · You can't adjust the surround back channel level when you're listening to the virtual surround back channel.
STANDARD ADVANCED SURROUND NEO:6 CINEMA/ NEO:6 MUSIC All modes
Type of source
STANDARD decoding
MOVIE/MUSIC/ PROLOGIC
DTS-ES/Dolby Digital Matrix encoded multi-channel sources with 6. 1 surround Dolby Digital/DTS encoded multi-channel sources Dolby Digital/DTS encoded stereo sources, Stereo sources Analog 2-channel (stereo) source
ON AUTO ON AUTO
41
En
06
Playing sources
Using Loudness and Midnight listening
The Loudness listening feature can be used to get good bass and treble from music sources at low volume levels. The Midnight listening feature allows you to hear effective surround sound of movies at low volume levels. The effect automatically adjusts according to the volume at which you're listening. Each press cycles through the effects as follows:
1 Press TONE to select the frequency you want to adjust. 2 Use the MULTI JOG dial to change the amount of bass or treble as necessary. Wait about five seconds for your changes to be input automatically.
MIDNIGHT Off LOUDNESS
· You can only use the tone controls when STEREO/DIRECT is selected. They can't be used when SPEAKER A is switched off.
Playing other sources
· You can't use MIDNIGHT/LOUDNESS when DVD 7. 1 ch has been selected, or when listening to a DTS 96kHz/24 bit source.
DVD TV
RECEIVER
VCR
CD-R
MULTI CONTROL
Using the tone controls
Depending on what you are listening to, you may want to adjust the bass or treble using the front panel tone control.
RCV
CD
TUN
TVC
MULTI JOG ENTER
INPUT SEL
RECEIVER CONTROL
MASTER VOLUME
GNAL ELECT MIDNIGHT/ LOUDNESS SPEAKERS SB CH MODE TONE QUICK SETUP DOWN
MULTI JOG
UP
VIDEO INPUT
P DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
1 Turn on the power of the playback component. 2 Turn on the power of the receiver.
42
En
Playing sources
06
3 Select the source you want to playback. 4 Start playback of the component you selected in step 1.
Selecting the multi-channel analog inputs
If you have connected a decoder or a DVD player with multi-channel analog outputs to this receiver (page 19), you must select the analog multi-channel inputs for surround sound playback.
· When playback from the multi-channel inputs is selected, you can't use the INPUT ATT, TONE, and MIDNIGHT/ LOUDNESS buttons, as well as the STANDARD, ADVANCED SURROUND, and STEREO/DIRECT sound modes. [. . . ] · Avoid exposing the remote sensor on the front panel to direct light. · Press FL DIMMER on the remote control repeatedly to return to the default.
The display is dark or off.
· If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.
Resetting the main unit
Use this procedure to reset all the receiver's settings to the factory default. STANDBY/ON button
2 While holding down the TONE button, press and hold the for about three seconds.
3 When you see RESET?OK appears in the display to indicate that the receiver has been reset to the factory default settings.
76
En
Additional information
11
Specifications
Amplifier section
Continuous average power output of 110 watts* per channel, min. , at 8 ohms, from 20 Hz to 20, 000 Hz with no more than 0. 2 %** total harmonic distortion (front).
Signal-to Noise Ratio [EIA, at 1 W (1 kHz)]
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD, TV/SAT . [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PIONEER VSX-D912K
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PIONEER VSX-D912K will begin.