User manual PIONEER VSX-D912-S

[. . . ] Product Name: AUDIO/VIDEO MULTI-CHANNEL RECEIVER Model Number: VSX-D912-S, VSX-D912-S-S Responsible Party Name: PIONEER ELECTRONICS SERVICE INC. LONG BEACH, CA 90801-1760, USA Phone: 310­952­2915 IMPORTANT NOTICE ­ THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR. PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND D1-4-2-6-1_En KEEP IN A SECURE AREA. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] To use another MCACC preset, exit the System Setup menu and press MCACC to select it before pressing SETUP. 40 En The System Setup menu 07 After the Acoustic Calibration Equalization is set, you are given the option to check the settings on-screen. 1 Select `MCACC Data Check' from the Data Management setup menu. 4. Data Management 4a. MCACC Data Check 1. Speaker Setting 2. Channel Level 3. Speaker Distance 4. Standing Wave 5. Acoustic Cal EQ a. MCACC b. MCACC c. Memory d. Memory Data Check Data Copy Rename Clear Data Management This system allows you to store up to six MCACC presets, allowing you to calibrate your system for different listening positions (or frequency adjustments for the same listening position). 1 This is useful for alternate settings to match the kind of source you're listening to and where you're sitting (for example, watching movies from a sofa, or playing a video game close to the TV). From this menu you can check your current settings, copy from one preset to another, name presets for easier identification and clear any ones you don't need. :Return ENTER:Next :Return 2 Select the setting you want to check. · It is useful to do this while a source is playing so you can compare the different settings. 3 Select the MCACC preset that you want to check. Use the / buttons if necessary to switch speakers/ settings. 4a4. EQ Data Check 63Hz : 0. 0 MCACC M1 125Hz : 0. 0 Ch [SBL] 250Hz : 0. 0 500Hz : 0. 0 1kHz : 0. 0 2kHz : -1. 0 4kHz : -2. 0 8kHz : -4. 5 16kHz : -7. 0 TRIM : 0. 0 :Return 63 125 250 500 1k 2k 4k 8k 16k TRM 1 Select `Data Management' from the System Setup menu. See Making receiver settings from the System Setup menu above if you're not already at this screen. System Setup 1. Auto MCACC 2. Surr Back System 3. Manual MCACC 4. Data Management 5. Manual SP Setup 6. Input Setup 7. Other Setup : Exit 4. Data Management a. MCACC b. MCACC c. Memory d. Memory Data Check Data Copy Rename Clear 4 Press RETURN to go back to the Data Check menu, repeating steps 2 and 3 to check other settings. 4a2. Speaker Distance 4a3. Standing Wave MCACC M1. 1 2 3 f : 110Hz : 110Hz : 110Hz Q : 3. 0 : 3. 0 : 3. 0 A T : 12. 0dB : 10. 0dB : 12. 0dB T :Return MCACC L C R SR SBR SBL SL SW M1. MEMORY 1 : 10. 5ft : 9. 0ft : 10. 0ft : 8. 5ft : 7. 0ft : 8. 0ft : 8. 0ft : 11. 5ft :Return :Return 2 Select the setting you want to adjust. · MCACC Data Check ­ Check the settings for any of your MCACC presets using the on-screen display (see Checking MCACC preset data below). · MCACC Data Copy ­ Copy settings from one MCACC preset to another (see Copying MCACC preset data below). · Memory Rename ­ Name your MCACC presets for easy identification (see Renaming MCACC presets below). · Memory Clear ­ Clear any MCACC presets that you don't want (see Clearing MCACC presets below). 5 When you're finished, press RETURN. You will return to the Data Management setup menu. Copying MCACC preset data If you want to manually adjust the Acoustic Calibration EQ (see Manual MCACC setup above), we recommend copying your current settings2 to an unused MCACC preset. OVER' and set the crossover frequency. 4 Frequencies below this point will be sent to the subwoofer (or LARGE speakers). You will return to the Manual SP Setup menu. 2 Choose the set of speakers that you want to set then select a speaker size. Use / to select the size (and number) of each of the following speakers:1 · Front ­ Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn't connect a subwoofer. · Center ­ Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn't connect a center speaker, choose NO (the center channel is sent to the other speakers). · Surr ­ Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn't connect surround speakers choose NO (the sound of the surround channels is sent to the other speakers). · SB ­ Select the number of surround back speakers you have (one, two or none). 2 Select LARGE if your surround back speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. ­ LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES is selected. [. . . ] Since hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries Association's Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise. Decibel Level Example 30 40 50 60 70 80 Quiet library, soft whispers Living room, refrigerator, bedroom away from traffic Light traffic, normal conversation, quiet office Air conditioner at 20 feet, sewing machine Vacuum cleaner, hair dryer, noisy restaurant Average city traffic, garbage disposals, alarm clock at two feet. Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. [. . . ]