User manual PIONEER VSX-D812-K

[. . . ] If connected to an AC outlet, the cut-off plug can cause severe electrical shock. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when D3-4-2-2-1a_A_En on vacation). WARNING ­ TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. D1-4-2-1_En CAUTION ­ PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD. RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. ATTENTION ­ POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE D2-4-4-1_EF A DECOUVVERT. WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm. [. . . ] · Second Zone ­ Select to use the (surround back) B speaker terminals to listen to stereo playback in another room (see Second Zone speaker B setup on page 54). · Front Bi-Amp ­ Select this setting if you're bi-amping your front speakers (see Biamping your front speakers on page 55). You return to the System Setup menu. Français Italiano Nederlands Manual MCACC speaker setup You can use the settings in the Manual MCACC setup menu to make detailed adjustments when you're more familiar with the system. Before making these settings, you should have already completed Automatically setting up for surround sound (MCACC) on page 9. You only need to make these settings once (unless you change the placement of your current speaker system or add new speakers). Important · For some of the settings below, you'll have to connect the setup microphone to the front panel and place it about ear level at your normal listening position. If you're doing this for the first time, you might want to make these settings in order. · Fine Ch Level ­ Make fine adjustments to the overall balance of your speaker system (see Fine Channel Level below). · Fine SP Distance ­ Make precise delay settings for your speaker system (see Fine Speaker Distance on page 36). The last five settings are specifically for customizing the parameters explained in Acoustic Calibration EQ below: · EQ AUTO Setting ­ Measure the acoustic characteristics of your room and automatically adjust the frequency balance of your speaker system (see Setting the Acoustic Calibration EQ automatically below). · EQ Data Copy ­ Copy Acoustic Calibration EQ settings for manual adjustment (see Copying your Acoustic Calibration EQ settings below). Español 35 En 07 The System Setup menu · EQ CUSTOM1/2 Adjust ­ Make detailed manual adjustments to your custom Acoustic Calibration EQ settings (see Setting the Acoustic Calibration EQ manually on page 38). · For comparison purposes, the reference speaker will change depending on which speaker you select. · If you want to go back and adjust a channel, simply use / to select it. You return to the Manual MCACC setup menu. Español Acoustic Calibration EQ Acoustic Calibration Equalization is a kind of room equalizer for your speakers (excluding the subwoofer). It works by measuring the acoustic characteristics of your room and neutralizing the ambient characteristics that [ [ [ ] ] ] ] ] :Cancel :Cancel As the receiver outputs test tones, the frequency balance is adjusted automatically for the following settings: 37 En 07 The System Setup menu · ALL CH ADJUST ­ A `flat' setting where all the speakers are set individually so no special weighting is given to any one channel. · FRONT ALIGN ­ All speakers are set in accordance with the front speaker settings (no equalization is applied to the front left and right channels). You return to the Acoustic Cal EQ setup menu after the Acoustic Calibration Equalization is set. For more on the ALL CH ADJUST and FRONT ALIGN settings, see Setting the Acoustic Calibration EQ automatically above. Select `OK' to copy and confirm. Setting the Acoustic Calibration EQ manually Before manually adjusting the Acoustic Calibration EQ, we recommend copying the ALL CH ADJUST or the FRONT ALIGN settings from the auto setup above (or from Automatically setting up for surround sound (MCACC) on page 9) to one of the custom settings. Instead of just a flat EQ curve, this will give you a reference point from which to start (see Copying your Acoustic Calibration EQ settings above for how to do this). 1 Select `EQ CUSTOM1 Adjust or EQ CUSTOM2 Adjust' from the Manual MCACC setup menu. 3. Manual MCACC a. Fine Ch Level b. Fine SP Distance c. EQ AUTO Setting d. EQ Data Copy e. EQ CUSTOM1 Adjust f . EQ CUSTOM2 Adjust g. EQ Data Check :Return 3e. EQ CUSTOM1 Adjust Test Tone Type ALL CH ADJUST Copying your Acoustic Calibration EQ settings If you want to manually adjust the Acoustic Calibration EQ (see Setting the Acoustic Calibration EQ manually below), we recommend copying the ALL CH ADJUST or the FRONT ALIGN settings from the EQ AUTO setup above (or from Automatically setting up for surround sound (MCACC) on page 9) to one of the custom settings. Instead of just a flat EQ curve, this will give you a reference point from which to start. [. . . ] IN CANADA - EXCEPT AS EXPRESSLY PROVIDED HEREIN, THERE ARE NO REPRESENTATIONS, WARRANTIES, OBLIGATIONS OR CONDITIONS, IMPLIED, STATUTORY OR OTHERWISE, APPLICABLE TO THIS PRODUCT. TO OBTAIN SERVICE PUSA and POC have appointed a number of Authorized Service Companies throughout the U. S. A. To receive warranty service y ou need to present your sales receipt or, if rented, your rental contract showing place and date of original owner's transaction. I f s hipping the unit you will need to package it carefully and send it, transportation prepaid by a traceable, insured method, to an Authorized Service Company. Package the product using adequate padding material to prevent damage in transit. [. . . ]