User manual PIONEER VSX-D510

[. . . ] AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D510 Operating Instructions WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE STANDBY/ON BUTTON IS SECONDARY CONNECTED AND THEREFORE DOES NOT SEPARATE THE UNIT FROM MAINS POWER IN STANDBY POSITION. IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] This feature will enable you to hear quiet sounds and not get jolted by loud or sudden sound effects. $ DVD 5. 1ch button Use this button to switch between a DVD player hooked up to the digital inputs and a 5. 1 ch external decoder hooked up to the 5. 1 ch analog inputs. % DSP MODE button (see page 24) Use to switch between the various DSP modes available (HALL1, HALL 2, JAZZ, DANCE, THEATER1, THEATER 2) and DSP off. Use to create different surround sound effects from any stereo source. ^ SIGNAL SELECT button (see page 23) Use to select between an analog or digital signal. & 2 /DTS button (see pages 23, 25) Use to switch between the various Dolby/DTS surround modes. * MASTER VOLUME Use to set the overall listening volume. 18 En Displays & Controls Display 1 SIGNAL SELECT 2 3 DIGITAL PRO LOGIC DSP 45 ATT 6 7 8 DIGITAL DTS ANALOG DIGITAL MONITOR RF ATT DIRECT SP A TUNED MIDNIGHT STEREO LOUDNESS MONO dB 9 0 -= ~ ! @ 1 SIGNAL SELECT indicators Lights to indicate the type of input signal assigned for the current component : 2 DIGITAL : Lights when a DOLBY DIGITAL signal is played. 3 2 DIGITAL indicator When the 2 (DOLBY)/DTS mode of the receiver is on, this lights to indicate playback of a Dolby Digital signal. However, 2 PRO LOGIC lights during two channel playback of Dolby Digital. 4 OVERLOAD indicator This lights when an analog signal is too high (the SIGNAL SELECT would have to be on ANALOG). It indicates the sound is distorting and the input signal should be reduced. 5 ATT indicator Lights when ATT is used to attenuate (reduce) the level of the input signal (can only be used in ANALOG mode). This function bypasses all tone, balance, DSP and Dolby Surround effects. Used to hear a recording as it's being made (see page 28). 9 CHARACTER display Shows the radio frequency or function (DVD/LD, CD, etc. ) receiver is using . 0 2 PRO LOGIC indicator When the 2 (DOLBY)/DTS mode of the receiver is on, this lights to indicate playback of a two channel source. - DSP indicator Lights when any Advanced Theater or DSP mode is selected. TUNER indicators MONO: Lights when the mono mode is set using the MPX button. TUNED: Lights when a broadcast is being received. STEREO: Lights when a stereo FM broadcast is being received in auto stereo mode. ---dB indicates the minimum level, and 0dB indicates the maximum level. · Depending on the level settings you make for individual channels, the MAX level can range between ­10dB and 0dB. 19 En Displays & Controls Remote Control Î = 1 2 3 MULTI CONTROL DVD/LD TV/SAT VCR/DVR CD CD-R/ RECEIVER TUNER TAPE/MD TV CONT 2 DSP MODE MIDNIGHT 5. 1CH 1 2 3 4 CHANNEL TEST SELECT TONE ATT SIGNAL SELECT 5 9 6 0 FUNC 7 EFFECT 8 ENTER CHANNEL LEVEL ~ 10 CH DISC 4 5 6 7 8 9 0 - VOL TV CONTROL FQ ST ENTER ST VOL ! TOP MENU MENU FQ @ # $ % ^ SOURCE CLASS MPX BAND 7 D. ACCESS 8 4 3 ¢ CHANNEL 1 ¡ LOUDNESS FUNCTION MUTING FL REMOTE MASTER RECEIVER DIMMER SETUP VOLUME AUDIO/VIDEO PRE-PROGRAMMED REMOTE CONTROL UNIT 1 MULTI CONTROL buttons Use to put the receiver/remote control in the stated mode. For other equipment controls, see Controlling the Rest of Your System on pages 31-32. 2 RECEIVER button (see page 13) Use this button when setting up the surround sound for the receiver. 3 NUMBER/MODE buttons (see pages 26, 31, 32) Use the number buttons to select the radio frequency in tuner DIRECT ACCESS mode or the tracks in CD, DVD mode etc. [. . . ] 1 Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Video Section Input (Sensitivity/Impedance) VCR/DVR, DVD/LD, TV/SAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p/75 Output (Level/Impedance) VCR/DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p/75 Frequency Response VCR/DVR, DVD/LD, TV/SAT MONITOR +0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]