User manual PIONEER VSX 924

[. . . ] Operating Instructions AV Receiver VSX- 924 -K/-S CAUTION TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Operating Environment D3-4-2-1-1_B1_En WARNING Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light). D3-4-2-1-7c*_A2_En Information for users on collection and disposal of old equipment and used batteries Symbol for equipment These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation. Symbol examples for batteries By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. [. . . ] When connected to a video device using the component video input, set this setting to ON and watch with the HDMI output. When set to a resolution with which the TV (monitor) is not compatible, no picture is output. Also, in some cases no picture will be output due to copyright protection signals. When AUTO is selected, the resolution is selected automatically according to the capacity of the TV (monitor) connected by HDMI. When PURE is selected, the signals are output with the same resolution as when input (see About the video converter on page ​ 3​ . When 1080/24p or 4K/24p is selected, the movement may be unnatural or the picture unclear, depending on the video signal being input. In this case, set the resolution to something other than 1080/24p or 4K/24p. When PURE is selected and the input signal is 480i, the on-screen display cannot be displayed. This setting have the effect only for pictures recorded in the interlaced scan format (480i/576i or 1080i signals). d Adjustment is not possible unless V. ADJ (Advanced Video Adjust) is set to MEMORY. This setting is only displayed when the video signals below are being input: — 480i, 576i, 480p, 576p, 720p, 1080i analog video signals — 480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video signals f This adjustment is only possible when 480i signals are being input from the composite video jacks. If the image doesn’t match your monitor type, adjust the aspect ratio on the source component or on the monitor. This setting is only displayed when 480i/p or 576i/p video signals are being input. 0 d (The image is only an example for checking the effect. ) 70 09 Switching the output (OUTPUT PARAMETER) You can press OUT P. to switch the output of speaker terminals or HDMI terminals to be played. Using other functions Switching the HDMI output Set which terminal to use when outputting video and audio signals from the HDMI output terminals. The HDMI OUT 1 terminal is compatible with the Control with HDMI function. 　 　 　 　 Switching the speaker terminals If you selected Normal(SB/FH), Normal(SB/FW) or Speaker B at Speaker system setting on page ​ 9​ you can 8 , switch between speakers using the OUT P. If you selected Front Bi-Amp, ZONE 2 or HDZONE, the button will simply switch your main speaker terminals on or off. 1 Press OUT P. . 2 Use i/j to select ‘OUT 1/2’. 3 Use k/l to select the setting. Please wait a while when Please wait . . . The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed. ! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV’s remote control. ! When MAIN/HDZONE is set to HDZONE, it is not possible to switch to OUT 2 (page ​ 4​ . 9 ) 1 Press OUT P. . ! You can perform the same operation by pressing SPEAKERS on the front panel. 2 Use i/j to select ‘SP’. [. . . ] 2. 4 GHz Modulation system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FH-SS (Frequency Hopping Spread Spectrum) Supported Bluetooth profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2DP, AVRCP Supported Codec. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SBC (Subband Codec), AAC, aptX Supported contents protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCMS-T Notes ! These specifications are applicable when the power supply is 230 V. ! Specifications and the design are subject to possible modifications without notice, due to improvements. [. . . ]