User manual PIONEER VSX-2021

[. . . ] VSX-LX55 VSX-202 1-K IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT: THE MOULDED PLUG This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362. [. . . ] The subwoofer output depends on the settings you made in Manual speaker setup on page 67 . However, if SP: B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed). All speaker systems (except Speaker B connections) are switched off when headphones are connected. 3 Use the INPUT SELECTOR dial to select the source for the zone you have selected. For example, ZONE 2 DVD sends the source connected to the DVD inputs to the primary (ZONE 2) sub room. If you select TUNER, you can use the tuner controls to select a preset station (see Saving station presets on page 33 if you're unsure how to do this). Therefore, changing the station in one zone also En 51 09 Using other functions changes the station in the other zone. Please be careful not to change stations when recording a radio broadcast. Making an audio or a video recording You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV). Keep in mind you can't make a digital recording from an analog source or vice-versa, so make sure the components you are recording to/from are hooked up in the same way (see Connecting your equipment on page 11 for more on connections). The receiver's volume, Audio parameters (the tone controls, for example), and surround effects have no effect on the recorded signal. Some digital sources are copy-protected, and can only be recorded in analog. Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use the same type of video cable for connecting your recorder as you used to connect your video source (the one you want to record) to this receiver. For example, you must connect your recorder using Component video if your source has also been connected using Component video. 4 When Speaker System is set to ZONE 2, use the MASTER VOLUME dial to adjust the volume for the sub zone. 5 When you're finished, press MULTI-ZONE CONTROL again to return to the main zone controls. You can also press MULTI-ZONE ON/OFF on the front panel to switch off all output to the sub zone(s). You won't be able to switch the main zone off completely unless you've switched off the MULTI-ZONE control first. If you don't plan to use the MULTI-ZONE feature for a while, turn off the power in both the sub and main rooms so that this receiver is in standby. recorder if you are unsure how to do this. Most video recorders set the audio recording level automatically-check the component's instruction manual if you're unsure. !If any zone is on, the sleep timer continues functioning. 5 Start recording, then start playback of the source component. Dimming the display You can choose between four brightness levels for the front panel display. Note that when selecting sources, the display automatically brightens for a few seconds. Reducing the level of an analog signal The input attenuator lowers the input level of an analog signal when it's too strong. You can use this if you find that the OVER indicator lights often or you can hear distortion in the sound. The attenuator isn't available with digital sources, or when using the Stream Direct (ANALOG DIRECT) modes. % Press to the receiver operation mode, then press DIMMER repeatedly to change the brightness of the front panel display. !In this case, the FL OFF indicator lights. MULTI-ZONE remote controls Press the remote control's ZONE 2 or ZONE 3 to operate the corresponding zone. The following table shows the possible MULTIZONE remote controls: Button(s) u INPUT SELECT Input function buttons MASTER VOLUME +/­ <a> MUTE <a> % Press to the receiver operation mode, then press A. ATT to switch the input attenuator on or off. Switching the HDMI output Set which terminal to use when outputting video and audio signals from the HDMI output terminals. The HDMI OUT 1 terminal is compatible with the Control with HDMI function. Using the sleep timer The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. [. . . ] 16 W to 8 W, less than 8 W to 6 W (setting required) Signal-to-Noise Ratio (IHF, short circuited, A network) LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 dB Frequency Response . . . . . 5 Hz to 100 000 Hz dB (Pure Direct Mode) Input (Sensitivity/Impedance) LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 mV/47 kW Output (Level/Impedance) REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 mV/2. 2 kW Digital In/Out Section HDMI terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-pin (Not DVI) HDMI output type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 55 mA USB terminal . . . . . . . . . . . . USB2. 0 Full Speed (Type A) iPod terminal . . . . . . . . . USB, and Video (Composite) ADAPTER PORT terminal . . . . . . . . . . . . . . . . . . 5 V, 100 mA WIRELESS LAN ADAPTER terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 600 mA Number of Furnished Parts MCACC Setup microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]