User manual PIONEER TS-A132CI

[. . . ] If this occurs, switch the system power off and check the power supply and speaker connections. Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health. [. . . ] 1 GAIN (gain) control If output remains low, even when the car stereo volume is turned up, turn controls to lower level. If distortion occurs when the car stereo volume is turned up, turn these controls to higher level. For use with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL position. For use with an RCA equipped Pioneer car stereo, with maximum output of 4 V or more, adjust level to match that of the car stereo output. If you hear too much noise when using the speaker input terminals, turn the gain control to higher level. Protective function included to prevent malfunction of the unit and/or speakers due to excessive output, improper use or improper connection. , this function cuts off the output for a few seconds as a normal function, but output is restored when the volume of the head unit is turned down. A cut in sound output may indicate improper setting of the gain control. To ensure continuous sound output with the head unit at a high volume, set amplifier gain control to a level appropriate for the preout maximum output level of the head unit, so that volume can remain unchanged and to control excess output. Despite correct volume and gain settings, the unit sound still cuts out periodically. in such cases , please contact the nearest authorized Pioneer Service Station. For other amplifiers, please follow the speaker output connection diagram for bridging shown on rear: two 8 W speakers in parallel for a 4 W load or a single 4 W speaker per channel. For any further enquiries, contact your local authorized Pioneer dealer or customer service. En 7 Section 03 Connecting the units About suitable specification of speaker Ensure speakers conform to the following standards, otherwise there is a risk of fire, smoke or damage. Speaker impedance is 2 W to 8 W for stereo connection, or 4 W to 8 W for monaural and other bridge connection. 300 W Two-channel input (Stereo) When connecting two speakers (Left and right) 3 4 1 2 1 2 3 4 5 6 Speaker output (Right) Speaker output (Left) RCA input jack A RCA input jack B RCA cable (sold separately) From car stereo (RCA output) 5 6 Other than subwoofer Speaker channel Two-channel output One-channel output Power MAX input: Min. 600 W Two-channel input (Stereo) When connecting a speaker (Bridge) Connecting the speakers and RCA input The RCA input mode can be two-channel (stereo) or one-channel (mono). 2 3 1 5 1 2 3 4 5 Speaker output RCA input jack A RCA input jack B RCA cable (sold separately) From car stereo (RCA output) 4 One-channel input (Mono) When connecting two speakers (front left and rear left) !8 En Section Connecting the units 03 English WARNING 3 If the battery wire is not securely fixed to the terminal using the terminal screws, there is a risk of overheating, malfunction and injury, including minor burns. 4 1 5 2 1 2 3 4 5 Front speaker output (Left) Rear speaker output (Left) RCA input jack A RCA cable (sold separately) From car stereo (RCA output) 1 Route battery wire from engine compartment to the vehicle interior. After completing all other amplifier connections, finally connect the battery wire terminal of the amplifier to the positive (+) battery terminal. 1 2 3 4 5 Positive (+) terminal Engine compartment Vehicle interior Fuse (30 A) × 2 Insert the O-ring rubber grommet into the vehicle body. [. . . ] € Places where it may interfere with the driver, such as on the floor in front of the driver’s seat. Install tapping screws in such a way that the screw tip does not touch any wire. This is important to prevent wires from being cut by vibration of the car, which can result in fire. Make sure that wires do not get caught in the sliding mechanism of the seats or touch the legs of a person in the vehicle as short-circuit may result. [. . . ]