User manual PIONEER SC-LX85

[. . . ] SC-LX85 SC-LX7 5 IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT: THE MOULDED PLUG This appliance is supplied with a moulded three pin mains plug for your safety and convenience. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362. [. . . ] If the desired operations cannot be performed even though you have set the preset codes, the remote control signals of other devices can be learned directly. A series of the remote control operations for starting listening or viewing can be programmed. Multiple remote control codes can be set for the different input functions. RENAME Setting What it does Setting What it does This is a function for automatically turning off the power of devices connected to the receiver. This is a setting for changing only the remote control unit's operation screen, without changing the receiver's input, when the remote control unit's input function buttons are pressed. This is convenient for using the remote control unit for devices not connected to the receiver. The names of the input function buttons displayed on the remote control unit can be changed as desired. Input function names changed on the receiver can be acquired by the remote control unit so that the names are the same on the remote control unit. See Renaming input function names in synchrony with the receiver on page 72. This function is used to erase remote control codes that have been learned. Codes learned for the different input functions can be erased individually. This function is for selecting wireless (RF) or infrared (IR) as the remote control operating mode for the different devices. See Operating this receiver by RF communications on page 71 and Operating other components by RF communications on page 71. The remote control unit's operation screen switches automatically when the receiver's input is switched (This is OPERATION only valid when the operation selector MODE switch is set to SOURCE). See Resetting the input assignment of one of the input function buttons on page 66. This is a function for resetting all remote control unit settings you have made to the defaults set upon shipment from the factory. The preset codes set for the different input functions can be checked. If you have multiple Pioneer receivers, amplifiers, etc. , this setting can be used to prevent other units from operating simultaneously when the remote control unit is operated. Exits the setup menu. is switched by inputting the preset code to set the remote control setting. This function is only valid when RECEIVER is set to IR MODE at the remote control's IR/RF SELECT setting (page 71). Set the remote modes on the receivers before using this function (see Remote Control Mode Setup on page 92). SYSTEM OFF KEY RESET 1 Check that the remote control's MULTI-ZONE selector switch is set to MAIN and that the operation selector switch is set to RECEIVER. 2 While pressing MULTI OPERATION, press HOME MENU. The remote display shows SETUP MENU. DIRECT FUNC ALL RESET 3 Use i/j to select `CHANGE RC MODE', then press ENTER. To operate another receiver, start over from step 1 to input its preset code. READ PRESET ID CHANGE RC MODE PRESET RECALL SYNC RENAMING EXIT SETUP Setting the remote to control other components Most components can be assigned to one of the input function buttons (such as DVD or CD) using the component's manufacturer preset code stored in the remote. [. . . ] 75 W unbalanced Frequency Range (AM) . . . . . . . . 531 kHz to 1602 kHz Antenna (AM) . . . . . . . . . . . . . . 435 mm (W) x 185. 6 mm (H) x 440. 3 mm (D) Weight (without package) SC-LX85 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17. 6 kg Video Section Signal level Composite Video . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 W) Component Video . . . . . . . . . . . . . Y: 1. 0 Vp-p (75 W), PB/PR: 0. 7 Vp-p (75 W) Corresponding maximum resolution Component Video . . . . . . . . . . . . . . . . . . . 1080p (1125p) (Video convert off) Number of Furnished Parts In case of SC-LX85 MCACC Setup microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 RF adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]