User manual PIONEER PRO-800HD

[. . . ] PLASMA DISPLAY PRO-1000HD PRO-800HD Operating Instructions Safety Precautions The following symbols are found on labels attached to the product. They alert the operators and service personnel of this equipment to any potentially dangerous conditions. IMPORTANT NOTICE The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCESSIBLE. WARNING This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage. CAUTION: CAUTION This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death. i ii PRO-1000HD / PRO-800HD Safety Precautions IMPORTANT SAFETY INSTRUCTIONS READ INSTRUCTIONS -- All the safety and operating instructions should be read before the product is operated. [. . . ] If no connections are made to these terminals, on-screen setup is not necessary. · When the menu screen is displayed, changing the signal input will cause the menu screen to turn off. · If the input computer signal is not supported by the display, the following message will be displayed: I NPUT 1 CA U T I O N U N S UP P O R T E D S I G N AL fH: fV: 7 7. 0 H z 1 15 2X 864 FUL L 2, 5 I NPUT 1 2, 5 3 S-VIDEO VIDEO 3 CA U T I O N OU T OF R A N G E f H : 7 5. 0 H z ­­­­ FUL L 4 4 Main Unit Operating Panel Remote Control Unit Use VOLUME +/­ on the remote control unit to adjust the volume. If no audio connections are made to this unit, this step is not necessary. When viewing is finished, press STANDBY/ON to put the unit in standby mode. The STANDBY/ON indicator will blink and then remain lit (red) indicating that the standby mode is engaged. Operation is not possible while the STANDBY/ON indicator is blinking (red). Switch MAIN POWER on the main unit to the off position to turn the main power off. The STANDBY/ON indicator may continue to light for a short while even after the main power is turned off. This is a result of residual electric load impressed on the circuitry, and the light will turn off presently. 5 1 Switch the main power switch on the main unit to the on position to turn the main power on. The STANDBY/ON indicator turns green. 6 2 CAUTION Please do not leave the same picture displayed on the screen for a long time. Doing so may cause a phenomenon known as "screen burn" which leaves a ghost, or residual, image of the picture on the screen. 20 PRO-1000HD / PRO-800HD Operations To adjust the volume To confirm display settings DISPLAY S-VIDEO VIDEO VOLUME +/­ Press VOLUME on the remote control unit. Operations Use VOLUME + or VOLUME ­ to adjust the volume of the connected speakers. Press DISPLAY on the remote control unit. The currently selected input, screen size and refresh rates will be displayed for about 3 seconds. V O L U ME : 5 I NPUT 1 To mute the sound fH: fV: 3 1. 0 H z 64 0X 480 D O T BY D OT MUTING Note The displayed refresh rates may be slightly different from the actual values. Press MUTING on the remote control unit. Press MUTING again to restore the sound. Muting is automatically canceled about 8 minutes after the button is pressed, and the volume level is adjusted to the minimum level. Press VOLUME + or VOLUME ­ to adjust the volume at a desired level. 21 PRO-1000HD / PRO-800HD Operations Screen Size Selection This unit incorporates screen modes of various height and width ratios. For optimal viewing, we recommend that you select the screen mode that best matches the video source that you are viewing. Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer's intentions. During video signal input How the picture looks WIDE Suitable for when viewing news or sports programs. Movies or sports programs can be viewed with an expansive powerful image. (To prevent screen burn on this display, the displayed position of the screen frame will be slightly different each time the power is turned on. ) Suitable for wide screen images (squeeze). Changing the screen size The size of the picture or the picture's range projected on the screen can be changed between 4 screen sizes described in the table on this page. FULL ZOOM Press SCREEN SIZE to select the size. The screen size changes each time SCREEN SIZE is pressed as follows. Mainly suitable for viewing Cinemascope size and other such movie images. Provides a more expansive, powerful image. [During video signal input] 3 WIDE ZOOM 2 3 DOT BY DOT FULL 2 3 4:3 FULL 2 3 4:3 During personal computer signal input 1 DOT BY DOT The input signal and the screen maintain a dot to line ratio of 1:1 and is thus highly faithful to the source. [PRO-1000HD] [During personal computer signal input] Consult the table Computer Signal Formats Supported (page 37) for information regarding screen sizes supported by each signal format. Notes ÷ When the WIDE, ZOOM or FULL setting is used to display a non-wide screen 4:3 picture fully on a wide screen, a portion of the picture may be cut off or appear deformed. [. . . ] 1 Speed clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Bead bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]