User manual PIONEER PRO-1410HD

[. . . ] Operating Instructions Thank you very much for purchasing this PIONEER product. Before using your Plasma Display, please carefully read the "Important Information" and these "Operating Instructions" so you will know how to operate the Plasma Display properly. You will find it useful in the future. Notes on Installation Work: This product is marketed assuming that it is installed by qualified personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. [. . . ] * When adjusting using the bar at the bottom of the screen, press the or button within 5 seconds. If not, the current setting is set and the previous screen appears. 01326 01326 LR -220+22 VIDEO 1-3 / COMPNT 1-2 / PC1DSUB / PC2-BNC VIDEO 1-3 / COMPNT 1-2 / PC1DSUB / PC2-BNC VIDEO 1-3 / COMPNT 1-2 / PC1DSUB / PC2-BNC ONOFF Sub menu 2 Sub menu 3 Sub menu 4 Main menu SCREEN ZOOM/4:3/FULL/WIDE/14:9/2. 35:1 -640+64 -1280+127 064 064 ONOFF*2 *2 064 *2 064128 Sub menu 2 Sub menu 3 Sub menu 4 Note: The main menu disappears by pressing the EXIT button. Main menu SET UP Sub menu LANGUAGE BNC INPUT D-SUB INPUT HD SELECT RGB SELECT HDMI SET UP COLOR SYSTEM BACK GROUND SIDE MASK S1/S2 DISPLAY OSD OSD ADJUST ALL RESET RESET NO YES YES NO YES NO NO YES YES YES YES YES -- REFERENCE 12 19 19 19 19 20 20 20 21 21 21 21 21 ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/ RGBCOMPONENT RGB 1080I/1035I/540P AUTO/STILL/MOTION/WIDE1/WIDE2/WIDE3/WIDE4/DTV COLOR1COLOR2 AUTO/PAL/PAL-M/PAL-N/PAL 60/SECAM/4. 43 NTSC/3. 58NTSC BLACK/GRAY 0. . . 3. . . 15 AUTOOFF ONOFF TOP LEFTTOP CENTERTOP RIGHTBTM LEFTBTM CENTERBTM RIGHT ONOFF 12 En 13 En OSD (On Screen Display) Controls English Main menu Sub menu POWER MGT. P DETECT ZOOM NAV PICTURE FREEZE LONG LIFE Sub menu 2 Sub menu 3 Sub menu 4 RESET YES YES YES YES YES YES YES YES YES YES YES YES YES REFERENCE 22 22 22 23 23 23 24 24 24 24 24 25 25 Picture Settings Menu Storing picture settings This function allows you to store in memory the current input signal and PICTURE menu settings and to recall these settings when necessary. There are six picture memories, and notes of up to 15 characters can be added to each. Example: Storing picture settings at MEMORY1 On "PICTURE MEMORY" of "PICTURE" menu, select "MEMORY1", then press the MENU/SET button. The "PICTURE MEMORY" screen appears. PICTURE MEMORY MEMORY1 SET INPUT : COMPNT1 SIGNAL : 480P NOTE : DVD/STAR WARS MEMORY2 INPUT : -- SIGNAL : -- NOTE : -- MEMORY3 INPUT : -- SIGNAL : -- NOTE : -- NEXT PAGE SEL. 1/2 RESET PICTURE MEMORY PREVIOUS PAGE MEMORY4 SET INPUT : -- SIGNAL : -- NOTE : -- MEMORY5 INPUT : -- SIGNAL : -- NOTE : -- MEMORY6 INPUT : -- SIGNAL : -- NOTE : -- SEL. MENU OK 2/2 RESET English On "CONTRAST" of "PICTURE" menu, adjust the contrast. PICTURE PICTURE MEMORY : OFF CONTRAST BRIGHTNESS SHARPNESS COLOR R TINT DNR : LOW COLOR TEMP. : MIDDLE GAMMA : 2. 1 LOW TONE : AUTO SET UP LEVEL :0 COLOR MGT PURECINEMA : ON AV SELECTION : DYNAMIC EXIT RETURN SEL. ADJ. G CONTRAST 10 Main menu SIGNAL INFO. Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESET -- REFERENCE 25 Note: If "CAN NOT ADJUST" appears . . . When trying to enter the PICTURE submenu, make sure AV SELECTION is not set to DEFAULT. Information Picture adjustment screen CONTRAST: Changes the picture's white level. Adjusting the computer image Only the contrast and brightness can be adjusted when a computer signal is connected. Restoring the factory default settings Select "DEFAULT" under the "AV SELECTION" settings. *1 Only when AUTO PICTURE is OFF. *2 PC only MENU OK EXIT RETURN Information Restoring the factory default settings Select "ALL RESET" under the SET UP menu. Note that this also restores other settings to the factory defaults. Information PICTURE MEMORY Settings OFF: Picture memory not used. Setting the memory · Use the L and M button to select the desired memory place, MEMORY1 to MEMORY6. · Use the and buttons to select "SET", then press the MENU/SET button. Resetting the memory Use the L and M button to select the desired memory place, MEMORY1 to MEMORY6, then use the and buttons to select "RESET", and finally press the MENU/SET button. The memory is cleared, and "--" is displayed in the "INPUT", "SIGNAL" and "NOTE" columns. Inputting notes · Use the and buttons to select "NOTE", then press the MENU/SET button. · When you have finished inputting the note, press the MENU/SET button. OSD (On Screen Display) Controls Reducing noise in the picture Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor. [. . . ] · Eliminate the light by closing curtains, pointing the light in a different direction, etc. · Operate the computer (move the mouse, etc. ). Monitor does not operate when the remote control's buttons are pressed. No sound or picture is produced. Picture appears but no sound is produced. · "IBM PC/AT" and "XGA" are registered trademarks of International Business Machines, Inc. · "Apple Macintosh" is a registered trademark of Apple Computer, Inc. [. . . ]