User manual PIONEER M-J310

[. . . ] 3 Pay close attention to all warnings in this manual and follow the instructions carefully. 4 Do not allow other persons to use this system until they have read and understood the operating instructions. 5 Do not install the display where it may (i) obstruct the driver's vision, (ii) impair the performance of any of the vehicle's operating systems or safety features, including air bags, hazard lamp buttons or (iii) impair the driver's ability to safely operate the vehicle. 6 Do not operate this display if doing so in any way will divert your attention from the safe operation of your vehicle. [. . . ] Adjustment range: Left:7 to Right:7 Auto EQ (auto-equalizer on/off) The auto-equalizer is an equalizer curve created by auto EQ (refer to Auto EQ (auto-equalizing) on page 32). Graphic EQ (equalizer adjustment) You can adjust the currently selected equalizer curve setting as desired. If you make adjustments when a curve other than Custom2 is selected, the equalizer curve settings will be stored in Custom1. If you make adjustments when the Custom2 curve is selected, the Custom2 curve will be updated. Powerful--Natural--Vocal--Custom1--Custom2--Flat--Super Bass 3 Push M. C. Adjustment range: +12dB to ­12dB Loudness (loudness) Loudness compensates for deficiencies in the lowand high-frequency ranges at low volume. Subwoofer1 (subwoofer on/off setting) This unit is equipped with a subwoofer output which can be turned on or off. Subwoofer2 (subwoofer adjustment) The cut-off frequency and output level can be adjusted when the subwoofer output is on. Only frequencies lower than those in the selected range are outputted from the subwoofer. 50Hz--63Hz--80Hz--100Hz--125Hz Bass Booster (bass boost) 28 En Section Operating this unit System settings 1 Display the system menu. After selecting, perform the following procedures to set the system function. Guide Info (guide information) 1 Press M. C. After selecting, perform the following procedures to set the initial setting. FM step (FM tuning step) Normally, the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. Auto PI (auto PI seek) The unit can automatically search for a different station with the same programming, even during preset recall. A-EQ Measurement (auto-equalizing) The auto-equalizer is an equalizer curve created by auto EQ (refer to Auto EQ (auto-equalizing) on the next page). Rear Speaker (rear output and subwoofer setting) Operating this unit Customizing the illumination color 1 Use M. C. The illumination color will be switched to the customized color. En 31 Section 03 Operating this unit This unit's rear output (rear speaker leads output and RCA rear output) can be used for full-range speaker (Full) or subwoofer (Subwoofer) connection. If you switch the rear output setting to Subwoofer, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, the unit is set for rear full-range speaker connection (Full). Even if you change this setting, there will be no output unless you turn the subwoofer output on (refer to Subwoofer1 (subwoofer on/off setting) on page 28). If you change this setting, subwoofer output in the audio menu will return to the factory settings. Video Signal (video signal setting) Be sure to adjust the video signal setting to one that is suitable for your country. [. . . ] PAL/SECAM compatible Durable temperature range (power off) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 W × 4 70 W × 1/2 W (for subwoofer) Continuous power output . . . 22 W × 4 (50 Hz to 15 000 Hz, 5 % THD, 4 W load, both channels driven) Load impedance . . . . . . . . . . . . . . . . . . . . . . 4 W (4 W to 8 W (2 W for 1 ch) allowable) Preout maximum output level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]