User manual PIONEER KEH-P8200RDS

[. . . ] Determine and resolve the cause, then replace the fuse with and identical equivalent. Do not install the amplifier on a surface that is not flat or on a surface with a protrusion. When installing the amplifier, do not allow parts such as extra screws to get caught between the amplifier and the automobile. Also, damage to this unit, smoke, and overheating could result from contact with liquids. [. . . ] Protective function included to prevent malfunction of the unit and/or speakers due to excessive output, improper use or improper connection. When outputting high volume sound etc. , this function cuts off the output for a few seconds as a normal function, but output is restored when the volume of the head unit is turned down. En 5 Section 02 Setting the Unit !A cut in sound output may indicate that the output level of the head unit and the input level of the amplifier do not match. To ensure continuous sound output with the head unit at a high volume, turn the amplifier level adjustment control right or left to a level appropriate for the preout maximum output level of the head unit to control excess output. Despite correct volume and level adjustment control settings, the unit sound still cuts out periodically. In such a case, please contact the nearest authorized Pioneer Service Station. If the amplifier level adjustment control is raised inappropriately, this will simply increase distortion, with little increase in power. If the signal waveform is distorted by high output, raising the level adjustment control of the amplifier only changes the power slightly. 6 En Section Connecting the units 03 Setting example In this system, connect this unit to 4 channels in 1, and 3 channels in 2. 3 1 7 4 5 2 7 6 Connection diagram d c 1 2 3 4 5 Connecting the units 8 d e f 9 a b e 7 6 c In this system, connect 2 channels to each unit. 3 7 4 7 5 7 6 7 a b 9 8 f 8 d e f 3 4 5 6 7 8 9 a b c d e f 9 c a b Tweeter Middle-range speaker Low-range speaker Subwoofer This unit High range output Mid range output Low range output Subwoofer output RS-P99 (sold separately) Optical cable IP-BUS cable Analog signal 1 Special red battery wire RD-228 (sold separately) After completing all other amplifier connections, finally connect the battery wire terminal of the amplifier to the positive (+) battery terminal. 2 Ground wire (Black) RD-228 (sold separately) Connect to a clean, paint-free metal location. 3 Car stereo with RCA output jacks (sold separately) 4 RS-P99 (sold separately) 5 External output If only one input plug is used, do not connect anything to RCA input jack B. 6 Connecting wire with RCA pin plugs (sold separately) 7 RCA input jack A 8 RCA input jack B En 7 Section 03 Connecting the units 9 Speaker output terminals Please see the following section for speaker connection instructions. Slide INPUT SELECT (input select) switch to 4CH position. 3 1 RCA input jack A For two-channel output, connect the RCA plugs to the RCA input jack A. 2 10 En Section Connecting the units 03 2 Connecting wires with RCA plugs (sold separately) 3 From RS-P99 (sold separately) etc. (RCA output) Connecting the power terminal Connecting the units WARNING !The use of a special red battery and ground wire RD-228, available separately, is recommended. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body. If the battery wire is not securely fixed to the terminal using the terminal screws, there is a risk of overheating, malfunction and injury, including minor burns. Solderless terminal connections !Do not connect cords with exposed core wires to the amplifier power terminals (power terminal, ground terminal, system remote control terminal), since disconnection or breakage may result in fire or shortcircuit. Fasten while ensuring the insulating sheath of the wire is not clamped. Use the supplied hexagonal wrench to tighten and loosen the terminal screw of the amplifier and use it to securely fasten the wire. Be careful to avoid excessive tightening of this screw, which may damage the wire. 1 Route battery wire from engine compartment to the vehicle interior. After completing all other amplifier connections, finally connect the battery wire terminal of the amplifier to the positive (+) battery terminal. 1 4 1 2 3 4 5 2 5 3 6 CAUTION Use the supplied hexagonal wrench to tighten the screws when fastening wires to the terminal. The use of a long, commercially available hexagonal wrench may exert excessive torque, possibly resulting in damage to the terminals and wires. Positive (+) terminal Engine compartment Vehicle interior Fuse (40 A) × 2 Insert the O-ring rubber grommet into the vehicle body. [. . . ] ±3 dB (L/R independent) Maximum input / Continuous input RCA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V / 2. 5 V (Super high-voltage mode on) Input impedance . . . . . . . . . . . . . . . . . . . . . 5 kW (Super high-voltage mode on) 22 kW (Super high-voltage mode off) Additional information Notes !Specifications and the design are subject to modifications without notice. [. . . ]