User manual PIONEER HDJ-2000-W

[. . . ] If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. € Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short. € Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. [. . . ] € Speakers connected to this unit must be highpower types with minimum rating of 50 W and impedance of 4 to 8 ohms. Connecting speakers with output and/or impedance values other than those noted here may result in the speakers catching fire, emitting smoke, or becoming damaged. € When this product’s source is switched ON, a control signal is output through the blue/white lead. Connect to an external power amp’s system remote control or the car’s Auto-antenna relay control terminal (max. If the car features a glass antenna, connect to the antenna booster power supply terminal. € When an external power amp is being used with this system, be sure not to connect the blue/white lead to the amp’s power terminal. Likewise, do not connect the blue/white lead to the power terminal of the auto-antenna. € To avoid short-circuiting, cover the disconnected lead with insulating tape. There is a possibility of short-circuiting if the leads are not insulated. € To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. € If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. GEX-P700DAB> IP-BUS cable (supplied with the DAB tuner) ITALIANO Black Blue A V-BUS cable (supplied with TV tuner) IP-BUS cable Multi-CD player (sold separately) Blue A V-BUS cable (supplied with TV tuner) Black Black NEDERLANDS When a DVD player (e. SDV-P7) is not used, use the AV-BUS cable (supplied with TV tuner) instead of the AV-BUS cable <CD-AB301E> (sold separately)*1 in the figure. Perform [VIDEO SETTING] correctly while referring to the Operation Manual. 4 6 Connecting the Units Connecting the system (B) This Product Remote sensor (supplied with Multi-DVD player) Yellow (VIDEO INPUT or BACK UP CAMERA) Black Blue Multi-DVD player (sold separately) < e. XDV-P9 > AV-BUS cable (supplied with the TV tuner) Blue Black IP-BUS cable (supplied with the TV tuner) IP-BUS cable (supplied with Multi-DVD player) Black Blue Not used. GEX-P6400TVP> Multi-CD player (sold separately) Black RCA cable (supplied with MultiDVD player) Perform [VIDEO SETTING] correctly while referring to the Operation Manual. When connecting an XDV-P9II, refer to the XDV-P9II’s Owner’s manual. 5 7 VIDEO Input / Output Connection Commercially available portable video component with RCA output (or back-up camera) ENGLISH This product To video output Yellow (video input) (VIDEO INPUT or BACK UP CAMERA) To audio outputs RCA cable (sold separately) ESPAÑOL 23 cm DEUTSCH White, Red (audio input L, R) (AUDIO INPUT) To video input Display with RCA input jacks 15 cm Yellow (rear display output) (REAR MONITOR OUTPUT) RCA cable (sold separately) FRANÇAIS Perform [VIDEO SETTING] correctly while referring to the Operation Manual. Noise filter To prevent the noise, use the supplied noise filters correctly. 7 8 Installation Note: • Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly. € Use only the parts included with the unit to ensure proper installation. [. . . ] € Do not place the display in a position where it will impede the driver’s visibility or affect the operation of your vehicle’s air bags. € The semiconductor laser will be damaged if it overheats, so don’t install the unit anywhere hot — for instance, near a heater outlet. € If installation angle exceeds 30° from horizontal, the unit might not give its optimum performance. 8 DIN Front/Rear-mount This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit chassis). [. . . ]