User manual PIONEER F-F6MK2-K

[. . . ] RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side). Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed. [. . . ] 8 MPX Use to switch between stereo and mono reception during FM broadcasts. If the signal is weak, switching to mono may improve the sound quality (page 15). TUNE When pressed during FM or AM mode, receivable stations are automatically stored in the preset memory in order starting from preset channel A1. Hold the button depressed for two seconds or longer during DAB mode to perform full scan operation (Full band and L-band). If the TUNED or STEREO indicator fails to light when tuning into an FM station due to a weak reception signal, press the MPX button to switch the tuner into mono reception mode. 1 This should improve the sound quality and allow you to enjoy the broadcast. 4 Either turn the TUNING/PRESET dial or press the / button to select the search mode. Steps 1 to 5 can be skipped when using the /, preset channel range (A to J) and station call (1 to 10) buttons. The preset mode is set when any of these buttons is pressed, regardless of the menu setting at that time. 1 The STEREO indicator will light blue when the MPX button is pressed. 4 Press the TUNING/PRESET dial or ENTER button to set the preset mode and make the preset channel number flash. ⷠSteps 1 to 4 can be skipped when using the MEMORY button. When this button is pressed, the preset memory standby mode is set, regardless of the menu setting at that time. 5 While the preset channel number is flashing, press one of the preset channel range (A to J) buttons to select the desired memory block (A to J). 6 While the preset channel number is flashing, either turn the TUNING/PRESET dial, press the / or Station call (1 to 10) button to select the desired preset channel (1 to 10). 1 7 While the preset channel number is flashing, either press the TUNING/PRESET dial or the MEMORY button to store the station in the preset memory. ⷠA total of 100 broadcast stations can be preset -- 10 stations (channels 1 to 10) in each of blocks A to J. 1 When the preset channel is A1, pressing the button or rotating the TUNING/PRESET dial to the left will cause the preset channel to move to J10. Radio Data System (RDS) is a system used by most FM radio stations to provide listeners with various kinds of information, such as the name of the station and the kind of show being broadcast. For example, you can search for a station that's broadcasting a show with the program type, JAZZ. You can search the following program types:1 POP M ­ Pop music ROCK M ­ Rock music EASY M ­ Easy listening LIGHT M ­ `Light' classical music CLASSICS ­ `Serious' classical music OTHER M ­ Music not fitting above categories WEATHER ­ Weather reports FINANCE ­ Stock market reports, commerce, trading, etc. CHILDREN ­ Programs for children SOCIAL ­ Social affairs RELIGION ­ Programs concerning religion PHONE IN ­ Public expressing their views by phone TRAVEL ­ Holiday-type travel information as opposed to traffic announcements. [. . . ] Operating this tuner with the remote sensor of your Pioneer amplifier Many Pioneer components have SR CONTROL jacks which can be used to link components together so that you can use just the remote sensor of one component. When you use a remote control, the control signal is passed along the chain to the appropriate component. Note that if you use this feature, make sure that you also have at least one set of analog audio jacks connected to another component for grounding purposes. 1 Connect the CONTROL IN jack of this tuner to the CONTROL OUT jack of your Pioneer amplifier. [. . . ]