User manual PIONEER DVR-65H-S

[. . . ] STANDBY/ON HDD DVD ORDER NO. OPEN/CLOSE REC ONE TOUCH COPY DV IN/OUT PULL-OPEN RRV2963 DVR-520H-S DVD RECORDER DVR-520H-S DVR-65H-S Model DVR-520H-S DVR-520H-S DVR-65H-S THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S). Type KU/CA KUXU/CA KCXU AC120V AC120V AC120V Power Requirement Region No. 1 1 1 Serial No. (*) : Initial Setup (Clock Setting, Remote Control Set, Channel settings, Video Out settings, Audio In settings, Audio Out settings, Language settings) Refer to the chapter 13 of the Operating Instructions for more details. An HDD (Hard Disc Drive) is mounted in this product. The HDD is a precision instrument very vulnerable to shock and electrostatic charges. Please read "7. 4 Cautions on Handling the HDD" in this manual and exercise sufficient caution when handling the HDD itself, as well as the product with the HDD built in. [. . . ] If SF is 44 kHz, it is considered that 44. 1-kHz audio is input, and sound is muted on the unit. SF QU AMODE [DVencode:XXX] TC RD RT ASPECT CGMS APSTB Sampling Frequency of DVdecode Stream QUANTIZATION of DVdecode Stream AUDIO MODE of DVdecode Stream = ~ Whether Yes (in the process of requesting DV Normally, Yes is indicated only with HDD or DVD playback output) or No is indicated in XXX TIME CODE of DVencode stream REC DATE of DVencode stream REC TIME of DVencode stream Aspect Ratio of DVencode stream CGMS of DVencode stream (common to video, audio ch1 and audio ch2) APS trigger bit of DVencode stream Normally, sources other than CGMS=00 are not output. C ! D E F 92 1 2 DVR-520H-S 3 4 Simple Diagnosis Location in the Debug Screen Items to be Checked, and Conditions Possible causes Symptoms 5 5 No operation for either DV input or output 1 Check the number of DV devices when one DV device is connected to the recorder: 01: The connected DV device is correctly identified. 7 Check of DV decoding when the recorder channel is set to DV: Yes: The recorder is in the process of a DV input operation No: The recorder is not executing a DV input operation Check the init indication: OK: Initialization of DV-related LSIs (IC5101, IC5202) appropriately completed Defective IC, defective soldering, defective power supply, NG: Communication failure between DV-related LSIs (IC5101, IC5202) and etc. Initialization of DV-related LSIs (IC5101, IC5202) has not been completed properly. Defective DV terminals, improper connection of the DV-terminal board, defective IC, defective cables, an IEEE 1394 device other than the DV device connected Defective IC, defective soldering, defective power supply, etc. 6 6 No picture nor sound for DV input 9 Check DEC: 525-60: An NTSC DV signal is input from the DV device. No: No DV signal is input from the DV device. Defective DV terminals, improper connection of the DV-terminal board, defective IC, defective source device Note: As to a model having the Input Line System setting, if the setting and the actual input signal system do not match, no picture appears. Recording cannot be performed for a copy-protected source. DVR-520H-S 9 Check CGMS: 00: A copy-permitted source is being input. 0 E D C DV input recording impossible No sound for DV input Check SF: 32 khz: An audio signal with 32-kHz sampling frequency is being input. 48 khz: An audio signal with 48-kHz sampling frequency is being input. 44 khz: An audio signal with 44. 1-kHz sampling frequency is being input. An audio signal with 44. 1-kHz sampling frequency is muted. 7 7 No picture nor sound for DV output Check DVencode during DVD/HDD playback: Yes: The recorder is in the process of a DV output operation No: The recorder is not executing a DV output operation (No is also displayed during playback of copy-prohibited sources or simultaneous-recording/playback. ) Defective IC, defective soldering, defective power supply, etc. 8 8 A B 93 F 1 2 3 4 7. 1. 6 ERROR RATE MEASUREMENT How to enter Error-Rate Measurement mode Press the ESC key then the SIDE-B key of the remote control unit for service to enter Error-Rate Measurement mode. During playback of DVD-VIDEO, Error-Rate Measurement mode can also be entered by pressing the ESC key then the PLAY key. The error-rate display disappears, and Error-Rate Measurement mode is exited. Note: The error rate cannot be measured in VR mode or during CD playback. A B Functions 1 Video-mode recording (recording medium) In this mode, DVD recording is automatically performed for 10 seconds, the recorded DVD title is played back while the error rate is being measured, then as soon as playback of the recorded DVD title is finished, playback stops. *1 After error-rate measurement is finished, the average error rate will be displayed on the FL display and OSD. Only in a case in which the calculation of the average error rate fails, the tray will open. 2 DVD-VIDEO (playback medium) Only during playback, when the ESC key then the SIDE-B key (or the ESC key then the PLAY key) are pressed, the error rate is calculated and displayed on the FL display and OSD. (2) Only in a case in which the calculation of the average error rate fails, the tray will open. Changes of display Table 1: Video mode (recording medium) C Operation "ERROR RATE" is displayed on the FL display for an instant. The recorded DVD title is played back while the error rate is being measured, then as soon as playback is finished it stops. After error-rate measurement is finished (1), the average error rate, the measurement-finish mark (), and the OK/NG-judgment result (3) will be displayed on the FL display and OSD. (If the tray opens as a result of NG judgment, the display on the FL display and OSD will be retained. ) Display FL Display ERROR ERROR xxxxx ER x . xE- x ERR RATE : x. xE-x RATE RATE OSD (On Screen Display) D ER x . xE- x ERR RATE : x. xE-x * OK Table 2: DVD-Video (playback medium) Operation Only during playback, when the corresponding keys are pressed, the error rate is calculated and displayed on the FL display and OSD. xE- x OSD (On Screen Display) ERR RATE : x. xE-x - After error-rate measurement is finished (1), the average error rate, the measurement-finish mark (), and the OK/NG-judgment result (3) will be displayed on the FL display and OSD. (If the tray opens as a result of NG judgment, the display on the FL display and OSD will be retained. ) ER x . xE- x ERR RATE : x. xE-x - OK F 94 1 2 DVR-520H-S 3 4 5 6 7 8 1 : Whether error-rate measurement is finished or not is judged, as shown in Table 3 below. Table 3: On judgment whether error-rate measurement is finished or not Recording Mode Judgment whether error-rate measurement is finished or not After playback of a certain amount () of data Measurement of the 16 ECC blocks is performed 16 times, then the grand sum is used for calculation of the error rate. The capacity is as follows: 16 ECC blocks × 16 sectors × 2048 bytes × 16 times = 8388608 bytes = 67108864 bits A Recording/playback duration required for error-rate measurement The time required for completion of error-rate measurement varies, depending on the input video signal to be recorded. [. . . ] 11 CH Channel indicator for the built-in TV tuner. D E F 144 1 2 DVR-520H-S 3 4 5 6 7 8 8. 4 REMOTE CONTROL Remote control 6 DVD Press to select the DVD for recording or playback. (When the recorder is stopped, press to change the tuner audio. ) SUBTITLE Displays/changes the subtitles included in multilingual DVD-Video discs. 8 PLAY MODE Press to display the Play Mode menu (for features such as search, repeat and program play). 9 Alphanumeric buttons and CLEAR Use the number buttons for track/chapter/title selection; channel selection, and so on. [. . . ]