User manual PIONEER DJM-5000

[. . . ] Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement. [. . . ] The level of attenuation can be chosen from 0 dB, ­3 dB, ­6 dB, ­12 dB. When only the L channel is connected, the input to the L channel will also be input into the R channel. When a digital-link cable is used to connect the unit to a PIONEER DJ CD player supporting digital linkage, the digital audio connections and control cable connections are performed at once, and functions such as BPM synchro are also enabled. Changes the volume with the BOOTH MONITOR dial (LEVEL), unaffected to the MASTER fader (since output is TRS, both balanced and unbalanced outputs are supported). When a digital link cable is used to connect the unit to a PIONEER video mixer (switcher) supporting digital-linkage, the video mixer's cross fader can be controlled using the cross fader of the DJM-5000. When only the L channel is connected, the input in the L channel will be input into the R channel. Before making or changing connections, switch off the power and disconnect the power cord from the AC outlet. When all other connections are completed, connect the supplied power cord to the AC inlet located on the rear panel of this unit, and connect the power plug to an AC outlet or auxiliary power socket on an amplifier. When using digital connections, connect the digital coaxial output connector to one of the DIGITAL input connectors of the DJM1000, and switch the input selector switch of the connected channel to [DIGITAL] (no digital input connectors are provided for channel 1 and channel 2). Other line level output devices 3 mm phone plug, connect to one of the LINE input connectors of the DJM-5000, and switch the input selector switch of the connected channel to [LINE] (no LINE input connectors are provided for channel 5 and channel 6). DJ CD player DJ CD player When using digital connections to devices such as CD players, connect the device's digital coaxial output connector to one of the DIGITAL input connectors of the DJM-5000, and switch the input selector switch of the connected channel to [DIGITAL] (no DIGITAL input connectors are provided for channel 1 and channel 2). Used to adjust the high-range sound of the booth monitor output signal. Used to adjust the low-range sound of the booth monitor output signal. When a digital link cable (mini DIN connector) is used to connect this unit to a PIONEER DJ effector with digital link support (EFX-1000), setting these buttons to ON enables fader effect functions. When the CROSS FADER ASSIGN switches for each channel are used to select [A] or [B], the cross fader start/ stop function of that channel's DJ CD player are turned ON/ OFF. When [THRU] is selected by the CROSS FADER ASSIGN switch for each channel, the channel fader start/stop function for that channel's DJ CD player is turned ON/OFF. The button for each channel lights up when the fader start/ stop function is turned ON, and is turned off when the fader start/stop function is turned OFF. Lights when a plug is inserted to the RETURN connector, or when a component supporting digital link is connected to the EFX connector. If the button is pressed when lighted, the function turns ON and the indicator flashes. When a digital-link component is connected to the EFX connector, the digital link component (digital signal) is given priority. When a digital link cable (mini DIN connector) is used to connect a PIONEER video mixer/switcher supporting digital link, the video mixer's cross fader can be operated using the cross fader of the DJM-5000. When this unit is connected via digital link to a PIONEER DJ effector with digital link support (EFX-1000), and a PIONEER DJ CD player with digital link support is also connected via digital link cable (mini DIN connector), setting these buttons to ON enables BPM sync functions. [. . . ] POST INSERT: Channel fader output, sent from before the cross fader assign, and returned to the same point. AUX: Channel fader output, sent from before the cross fader assign and returned to the point before the master fader, and then added to any other output. The original sound which has been sent will also be passed through the cross fader assign and added. If a cue point has already been set, the CD player does not have to be set to standby at the cue point. [. . . ]