User manual PIONEER DJM-250-W

[. . . ] Com/support/ The Pioneer website shown above offers FAQs, information on software and various other types of information and services to allow you to use your product in greater comfort. а а а а а , , а а а а Operating Instructions Mode d’emploi Bedienungsanleitung Istruzioni per l’uso Handleiding Manual de instrucciones И а а Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. [. . . ] Do not allow anything to pinch or rest on the power cord and do not place in a walkway. Power Turn OFF the system before installing this or any other hardware device. Side Top Overloading Avoid connecting too many devices to a single wall socket or power source as this can cause fires or short circuits. Object & Liquid Entry Never push inappropriate objects in to the device. The power plug could come detached from the AC adapter and remain in the power outlet if someone trips on the AC adapter’s power cord or if something hits the AC adapter. About the power switch of this unit To turn the power on Set the [ON/OFF] switch on this unit’s rear panel to [ON]. 2 MIC, OFF, AUX 1, AUX 2, AUX 3 input selector switch 3 LEVEL control (MIC/AUX section) 4 HI, LOW controls Headphones section The sound being input to this unit can be checked over headphones (page 12). 5 CH-1 , CH-2 buttons (headphones section) 6 MIXING control 7 LEVEL control (headphones section) 8 PHONES jack En 9 Basic operations (mixer section) TRIM CD 5 Move the crossfader f. This operation is not necessary when the [THRU, , ] (crossfader curve selector) switch is set to [THRU]. 9 PHONO /LINE CD PHONO /LINE TRIM a b 9 c HI MASTER CH-1 CH-2 OVER 9 HI a b 9 OVER 9 MID EQ d 9 +4 +2 0 -6 -12 -18 dB +4 +2 0 -6 -12 -18 dB d MID EQ 9 6 Turn the [MASTER LEVEL] control 1 clockwise. Adjust [MASTER LEVEL] so that the orange indicator lights at the point in the track where the volume is loudest (the climax, etc. Be careful that the red indicator does not light, or the sound could be distorted. 1 LOW LOW 2 9 9 LEVEL SOUND COLOR FILTER LPF HPF LPF HPF Adjusting the sound quality Turn the [CH-1] 1 or [CH-2] 2 EQ (HI, MID, LOW) control b. Refer to Specifications on page 14 for the range of sound that can be adjusted by each control. The sound for that range can be turned completely off by turning the control all the way counterclockwise (isolator function). E CH-1 CH-2 f Mixing using the faders Prepare the unit in advance so that the sound of [CH-1] 1 is being output from the speakers. Outputting sound Check that this unit is properly connected to the DJ player, etc. For instructions on connections, see Connecting the input/output terminals on page 6. Set the volume of the powered speakers connected to the [MASTER 1] and [MASTER 2] terminals to a suitable level. Note that sound will be output at a high volume if the volume is set too high. For instructions on monitoring the sound, see Monitoring the sound over headphones (headphones section) on page 12.  To output the sound of channel 1 [CH-1] 1 To output the sound of channel 2 ([CH-2]) 2, perform the procedure below replacing [CH-1] with [CH-2]. [. . . ] (page 6) Properly attach the included AC adapter’s power cord to this unit’s cord hook. Is the [CD, PHONO/LINE] input selector switch set to the proper position?Is the [PHONO/LINE] selector switch on this unit’s rear panel set to the proper position?Are the [TRIM], [channel fader], [crossfader] and [MASTER LEVEL] controls set to the proper positions? [. . . ]