User manual PIONEER DEX-P99R

[. . . ] For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. CAUTION !Also, damage to this unit, smoke, and overheating could result from contact with liquids. [. . . ] Turn MULTI-CONTROL to switch between the functions in the following order. Language select (language selection)-- SP connection (speaker setting)--Clock (clock)-- Off clock (off clock)--FM step (FM tuning step)--Auto PI (auto PI seek)-- Warning tone (warning tone)-- Face auto open (face auto open)--AUX1 (auxiliary input 1)--AUX2 (auxiliary input 2)-- Dimmer (dimmer)--Brightness (brightness) --Illumination 1 (illumination select)-- Illumination 2 (custom illumination)-- ILL line (illumination interlock)--Digital ATT (digital attenuation)--Audio Reset (audio reset)--Mute (sound muting/attenuation)-- Door mute 1 (intelligent mute polarity setting) --Door mute 2 (intelligent mute setting)-- Reverse mode (reverse mode)--Ever-scroll (ever scroll)--BT AUDIO (Bluetooth audio)-- Pin code input (pin code input)-- BT Version Info. (Bluetooth version information) Use the following instructions to operate each particular setting. Setting the speakers You need to set the speakers used with this system. When this setting is performed correctly, this unit reproduces high-definition sound suited to your system. If this setting is adjusted after performing auto-time alignment and auto-equalizing function, perform auto-time alignment and auto-equalizing again. 1 Use MULTI-CONTROL to select SP connection in the initial setting menu. Refer to Adjusting initial settings on this page. 38 En Section Initial Settings 2 Push MULTI-CONTROL left or right to select the speaker to be adjusted. Each time MULTI-CONTROL is pushed left or right, the speaker is selected in the following order: Subwoofer (subwoofer)--Low range (low range speaker)--High range (high range speaker) 3 Press MULTI-CONTROL to turn the selected speaker on. # To turn off, press MULTI-CONTROL again. 04 1 Use MULTI-CONTROL to select Off clock in the initial setting menu. 2 Press MULTI-CONTROL to turn the off clock display on. # To turn the off clock display off, press MULTI-CONTROL again. Initial Settings Setting the FM tuning step Normally the FM tuning step employed by seek tuning is 50 kHz. When AF or TA is on, the tuning step automatically changes to 100 kHz. Pressing MULTI-CONTROL repeatedly will switch the FM tuning step between 50 kHz and 100 kHz. This function can be used only when Custom is selected in Illumination 1. 1 Use MULTI-CONTROL to select Illumination 2 in the initial setting menu. R (red)--G (green)--B (blue) 3 Push MULTI-CONTROL up or down to adjust the level of color. When listening to a CD or other source on which the recording level is high, setting the level of each frequency to high may result in distortion. Sound quality is better at the high setting so this setting is usually used. 1 Use MULTI-CONTROL to select Digital ATT in the initial setting menu. Pressing MULTI-CONTROL repeatedly will switch between High (high) and Low (low) and that status will be displayed. Resetting the audio functions You can reset all audio functions. 1 Use MULTI-CONTROL to select Audio Reset in the initial setting menu. appears in the display. Setting the illumination interlock This unit's button illumination can be interlocked with either the ignition key or the vehi- En 41 Section 04 Initial Settings 3 Push MULTI-CONTROL right. Complete appears in the display and audio functions are reset. # To cancel this function on the way, press B. 2 Press MULTI-CONTROL to select setting. Each press of MULTI-CONTROL selects settings in the following order: High (high)--Low (low) ! [. . . ] 25/31. 5/40/50/63/80/100/125/ 160/200/250/315/400/500/ 630/800/1k/1. 25k/1. 6k/2k/ 2. 5k/3. 15k/4k/5k/6. 3k/8k/ 10k/12. 5k/16k/20k Hz Frequency (HPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20/25/31. 5/40/50/63/80/100/ 125/160/200/250/315/400/ 500/630/800/1k/1. 25k/1. 6k/ 2k/2. 5k/3. 15k/4k/5k/6. 3k/8k/ 10k/12. 5k/16k Hz Additional Information Audio/DSP Preout max output level . . . . . . . +10 dB (100 Hz), +6. 5 dB (10 kHz) (volume: ­30 dB) Equalizer (Left/Right independent 31-Band Graphic Equalizer): Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . 20/25/31. 5/40/50/63/80/100/ 125/160/200/250/315/400/ 500/630/800/1k/1. 25k/1. 6k/ 2k/2. 5k/3. 15k/4k/5k/6. 3k/8k/ 10k/12. 5k/16k/20k Hz Equalization range . . . . . . . . [. . . ]