User manual PIONEER DEH-P835R

[. . . ] For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. CAUTION !Also, damage to this unit, smoke, and overheating could result from contact with liquids. [. . . ] 2 Press MULTI-CONTROL to turn warning tone on. # To turn warning tone off, press MULTI-CONTROL again. 04 1 Use MULTI-CONTROL to select Brightness in the initial setting menu. 0 to 15 is displayed as the level is increased or decreased. # When dimmer is functioning, the brightness level can be adjusted 0 to 10. Initial Settings Switching the auxiliary setting Auxiliary devices connected to this unit can be activated individually. For more information about connecting or using auxiliary devices, refer to Using the AUX source on page 38. 2 Press MULTI-CONTROL to turn AUX1/ AUX2 on. # To turn AUX off, press MULTI-CONTROL again. Setting the rear output and subwoofer controller This unit's rear output (rear speaker leads output and RCA rear output) can be used for fullrange speaker (Rear SP :F. Range) or subwoofer (Rear SP :S/W) connection. If you switch the rear output setting to Rear SP :S/W, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp. Initially, the unit is set for rear full-range speaker connection (Rear SP :F. Range). 1 Use MULTI-CONTROL to select S/W control in the initial setting menu. Pressing MULTI-CONTROL will switch between Rear SP :F. Range (full-range speaker) and Rear SP :S/W (subwoofer) and that status will be displayed. # When no subwoofer is connected to the rear output, select Rear SP :F. Range (full-range speaker). # When a subwoofer is connected to the rear output, select Rear SP :S/W (subwoofer). Even if you change this setting, there is no output unless you turn the subwoofer output on (refer to Using subwoofer output on page 30). Switching the dimmer setting To prevent the display from being too bright at night, the display is automatically dimmed when the car's headlights are turned on. 2 Press MULTI-CONTROL to turn dimmer on. # To turn dimmer off, press MULTI-CONTROL again. Adjusting the brightness You can adjust the display brightness. En 35 Section 04 Initial Settings !When connected, auxiliary devices are automatically read as AUX sources and assigned to AUX1 or AUX2. The relationship between AUX1 and AUX2 sources is explained below. Setting the AUX title The title displayed for the AUX1 or AUX2 source can be changed. 1 After you have selected AUX as the source, use MULTI-CONTROL and select FUNCTION to display TitleInput "A". For details concerning operation, refer to Entering disc titles on page 20. About AUX1 and AUX2 There are two methods to connect auxiliary devices to this unit. Using the external unit AUX1 source: When connecting auxiliary device using a stereo mini plug cable % Insert the stereo mini plug into the input jack on this unit. External unit refers to a Pioneer product (such as ones available in the future) that, although incompatible as a source, enables control of basic functions with this unit. When two external units are connected, the external unit is automatically allocated to external unit 1 or external unit 2 by this unit. Allocated functions are different depending on the connected external unit. For details concerning functions, refer to external unit's owner's manual. AUX2 source: When connecting auxiliary device using an IPBUS-RCA Interconnector (sold separately) % Use an IP-BUS-RCA Interconnector such as the CD-RB20/CD-RB10 (sold separately) to connect this unit to auxiliary device featuring RCA output. For more details, refer to the IP-BUS-RCA Interconnector owner's manual. This auxiliary device is automatically set to AUX2. # You can only make this type of connection if the auxiliary device has RCA outputs. Selecting the external unit as the source % Press SRC/OFF to select EXTERNAL as the source. Basic operation Functions allocated to the following operations are different depending on the connected external unit. For details concerning functions, refer to the connected external unit's owner's manual. [. . . ] and other countries. iPhone is a trademark of Apple Inc. 64 En Appendix Additional Information Specifications General Power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14. 4 V DC (10. 8 V to 15. 1 V allowable) Grounding system . . . . . . . . . . . . . . . . . . . current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10. 0 A Dimensions (W × H × D): DIN Chassis . . . . . . . . . . . . . . . . . . . . . [. . . ]